When a key is inserted into the ignition key cylinder, the transponder key coil receives the key ID code and sends it to the transponder key ECU assembly.
If an error in communication between the transponder key coil and transponder key ECU assembly occurs, this symptom may occur.
If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
| Result | Proceed to |
|---|---|
| DTCs are not output (for Gasoline) | A |
| DTCs are not output (for Diesel) | B |
| DTCs are output | C |
A
B
C
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Immobiliser Fuel Cut | Status of immobiliser system fuel cut | ON or OFF | - | - |
| Tester Display |
|---|
| Immobiliser Fuel Cut |
OFF is displayed after the engine is started.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check that the security indicator light turns off when a registered key is inserted into the ignition key cylinder.
Security indicator light turns off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the security indicator light turns off when another registered key is inserted into the ignition key cylinder.
Security indicator light turns OFF.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using another registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transponder key coil.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY AMPLIFIER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| Engine can be started |
| Engine cannot be started |
Engine can be started
Engine cannot be started
Replace the transponder key ECU assembly with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the key.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the key.
Key ID code registration is necessary when replacing the key.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG (for 1GR-FE) |
| NG (for 1VD-FTV) |
| NG (for 1VD-FTV(w/ DPF)) |
OK
NG (for 1GR-FE)
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG (for 1VD-FTV)
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG (for 1VD-FTV(w/ DPF))