Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › 2017.09–2019.09
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B416730E27
1.979,0.896 2.438,1.094 0.458,0.198 10 false IMO 2.01,1.802 2.469,2 0.458,0.198 10 false IMI 1.802,1.49 2.26,1.688 0.458,0.198 10 false +B 0.729,2.99 1.188,3.188 0.458,0.198 10 false ECM 0.74,2.833 2.188,3.083 1.448,0.25 10 false A29*1, I84*2 2.344,1.792 3.323,2.063 0.979,0.271 10 false 11 2.333,0.885 3.323,1.146 0.99,0.26 10 false 10 4.729,0.896 5.188,1.094 0.458,0.198 10 false 12 4.75,1.792 5.208,1.99 0.458,0.198 10 false 13 5.063,0.896 5.521,1.094 0.458,0.198 10 false EFII 5.042,1.792 5.5,1.99 0.458,0.198 10 false EFIO 6.042,0.24 6.26,0.458 0.219,0.219 10 false +B 4.938,2.865 5.396,3.063 0.458,0.198 10 false L30 4.948,3.042 7.031,3.229 2.083,0.188 10 false Transponder Key ECU Assembly 1.979,3.063 3.51,3.396 1.531,0.333 10 false *1: for RHD 1.979,3.438 3.958,3.802 1.979,0.365 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC is not output.



Result:
Result Proceed to
DTCs are not output (for Gasoline) A
DTCs are not output (for Diesel) B
DTCs are output C



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.CHECK WHETHER ENGINE STARTS

C

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
5.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B489445C02
3.25,0.448 3.719,0.677 0.469,0.229 2.125,2 2.365,2 2.365,2 3.208,1.323 true 2.135,0.688 2.448,0.885 0.313,0.198 10 false *a 3.365,0.479 3.677,0.677 0.313,0.198 10 false L30 1.771,1.927 2.219,2.156 0.448,0.229 10 false EFIO 2.677,2.979 2.99,3.177 0.313,0.198 10 false *b 1.281,3.906 1.729,4.135 0.448,0.229 10 false GND
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform A


Measurement Condition
Item Content
Tester Connection L30-13 (EFIO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

OK:

Waveform is output normally (refer to illustration).


Result:
Result Proceed to
Normal waveform A
Waveform A not output, or has abnormal wavelength or shape B




A

6.CHECK ECM (TERMINAL IMO)

B

14.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
6.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B489446C02
3.24,0.458 3.656,0.677 0.417,0.219 2.5,2.073 2.719,2.073 2.719,2.073 3.354,1.344 false 2.167,0.729 2.479,0.927 0.313,0.198 10 false *a 3.333,0.479 3.646,0.677 0.313,0.198 10 false L30 2.313,3.021 2.625,3.219 0.313,0.198 10 false *b 1.313,3.906 1.854,4.219 0.542,0.313 10 false GND 2.198,1.99 2.635,2.25 0.438,0.26 10 false EFII 1.938,3.969 2.25,4.167 0.313,0.198 10 false *c 2.573,3.99 2.885,4.188 0.313,0.198 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform B
*c Approximately 160 ms *d Approximately 510 ms


Measurement Condition
Item Content
Tester Connection L30-12 (EFII) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

OK:

Waveform is output normally (refer to illustration).


Result:
Result Proceed to
Normal waveform A
Waveform B not output, or has abnormal wavelength or shape (for 1GR-FE) B
Waveform B not output, or has abnormal wavelength or shape (for 1VD-FTV) C




A

7.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

B

C

7.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B489447C02
3.229,0.479 3.646,0.698 0.417,0.219 2.094,2.052 2.292,2.052 2.292,2.052 3.198,1.323 true 2.208,0.677 2.521,0.875 0.313,0.198 10 false *a 3.323,0.5 3.74,0.719 0.417,0.219 10 false L30 1.271,3.896 1.688,4.115 0.417,0.219 10 false GND 3.708,3.01 4.125,3.229 0.417,0.219 10 false *b 3.26,4.021 3.677,4.24 0.417,0.219 10 false *c 3.906,4.042 4.323,4.26 0.417,0.219 10 false *d 1.708,1.969 2.125,2.188 0.417,0.219 10 false EFIO
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform C
*c Approximately 160 ms *d Approximately 510 ms


Measurement Condition
Item Content
Tester Connection L30-13 (EFIO) - Body ground*1
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

OK:

Waveform is output normally (refer to illustration).


Result:
Result Proceed to
Normal waveform A
Waveform C not output, or has abnormal wavelength or shape B




A

8.REGISTER ECU COMMUNICATION ID

B

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
8.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

NG

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.REGISTER KEY
11.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

12.REGISTER ECU COMMUNICATION ID
12.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

13.CHECK WHETHER ENGINE STARTS
13.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 1GR-FE)
NG (for 1VD-FTV)
NG (for 1VD-FTV(w/ DPF))



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG (for 1GR-FE)

NG (for 1VD-FTV)

NG (for 1VD-FTV(w/ DPF))

14.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the L30 transponder key ECU assembly connector.


b.

Disconnect the A29*1, I84*2 ECM connector.

*1: for RHD

*2: for LHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
L30-12 (EFII) - A29-10 (IMO) Always Below 1 Ω
L30-13 (EFIO) - A29-11 (IMI) Always Below 1 Ω
A29-10 (IMO) - Body ground Always 10 kΩ or higher
L30-12 (EFII) - Body ground Always 10 kΩ or higher
A29-11 (IMI) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
L30-12 (EFII) - I84-10 (IMO) Always Below 1 Ω
L30-13 (EFIO) - I84-11 (IMI) Always Below 1 Ω
I84-10 (IMO) - Body ground Always 10 kΩ or higher
L30-12 (EFII) - Body ground Always 10 kΩ or higher
I84-11 (IMI) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR