Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CYLINDER BLOCK › 2017.09–2019.09
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0132958 CYLINDER BLOCK A

1VD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 11432R 1.INSTALL CYLINDER BLOCK STRAIGHT SCREW PLUG

HINT:

If water leaks from the cylinder block straight screw plug or the plug is corroded, replace the straight screw plug.


a.

Install 4 new gaskets and the 4 cylinder block straight screw plugs.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 2.INSTALL CYLINDER BLOCK STUD BOLT

HINT:

If a cylinder block stud bolt is deformed or the threads are damaged, replace it.


a.

Using an E7 "TORX" wrench, install the cylinder block stud bolts labeled A shown in the illustration below.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Using an E8 "TORX" wrench, install the cylinder block stud bolts labeled B shown in the illustration below.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

A164621C01
0.427,0.438 0.74,0.594 0.313,0.156 10 false *a 0.427,2.448 0.74,2.604 0.313,0.156 10 false *b 4.979,1.25 5.292,1.406 0.313,0.156 10 false *c 4.979,3.5 5.292,3.656 0.313,0.156 10 false *d 0.906,2.188 1.063,2.385 0.156,0.198 10 false A 2.406,2.198 2.563,2.396 0.156,0.198 10 false A 4.323,0.083 4.479,0.281 0.156,0.198 10 false A 0.542,2.76 0.698,2.958 0.156,0.198 10 false B 0.635,4.135 0.792,4.333 0.156,0.198 10 false B 4.323,2.552 4.479,2.75 0.156,0.198 10 false B
*a Front Side *b Lower Side
*c 55 mm (2.17 in.) *d 35 mm (1.38 in.)



Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101A 4.INSTALL PISTON PIN HOLE SNAP RING

a.
A164624C01
2.458,1.573 2.771,1.729 0.313,0.156 10 false *a
*a Cutout Position


Using a screwdriver, install a new piston pin hole snap ring on one side of the piston pin hole.

HINT:

Be sure that the end gap of the piston pin hole snap ring is not aligned with the pin hole cutout portion of the piston.



Hide 13101 5.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.

Gradually heat the piston to approximately 80°C (176°F).


b.

Coat the piston pin with engine oil.


c.

for Bank 1:

i.
A168383C01
2.188,1.74 2.5,1.896 0.313,0.156 10 false *a 2.135,3.771 2.448,3.927 0.313,0.156 10 false *a
*a Front Mark


Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb.

HINT:
·

The piston and pin are a matched set.

·

The piston has 2 front marks.





d.

for Bank 2:

i.
A168384C01
2.094,1.75 2.406,1.906 0.313,0.156 10 false *a 2.115,3.76 2.427,3.917 0.313,0.156 10 false *a
*a Front Mark


Face the front marks of the piston and connecting rod in opposite directions, and push in the piston pin with your thumb.

HINT:
·

The piston and pin are a matched set.

·

The piston has 1 front mark.





e.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


Hide 13101A 6.INSTALL PISTON PIN HOLE SNAP RING

a.
A164802C01
0.688,1.708 1,1.865 0.313,0.156 10 false *a
*a Cutout Position


Using a screwdriver, install a new piston pin hole snap ring at the other end of the piston pin hole.

HINT:

Be sure that the end gap of the piston pin hole snap ring is not aligned with the pin hole cutout portion of the piston.



Hide 13011 7.INSTALL PISTON RING SET

a.
A164800

Install the oil ring expander by hand.


b.

Using a piston ring expander, install the oil ring rail.

HINT:

Align the oil ring rail ends and coil joint as shown in the illustration.


A316806C01
5.385,0.417 6.167,0.417 true 4.25,0.333 5.031,0.333 true 5.104,1.719 5.104,1.135 true 4.25,2.667 4.417,2.667 4.417,2.667 5.115,2.573 true 4.094,0.24 4.406,0.396 0.313,0.156 10 false *1 6.198,0.333 6.51,0.49 0.313,0.156 10 false *2 5.031,1.729 5.344,1.885 0.313,0.156 10 false *b 4.104,2.563 4.417,2.719 0.313,0.156 10 false *a
*1 Oil Ring Expander *2 Oil Ring Rail
*a Oil Ring Rail Ends *b Coil Joint



c.

Using a piston ring expander, install the No. 1 compression ring.

A316807C01
2.385,1.031 2.667,0.333 2.667,0.333 2.833,0.333 true 1.146,2.198 1.458,2.354 0.313,0.156 10 false *1 2.552,2.198 2.865,2.354 0.313,0.156 10 false *2 2.865,0.25 3.177,0.406 0.313,0.156 10 false *a
*1 No. 1 Compression Ring *2 No. 2 Compression Ring
*a Code Mark - -



d.

Using a piston ring expander, install the No. 2 compression ring so that the code mark is positioned as shown in the illustration.

HINT:
·

Install the No. 1 compression ring with no code mark. The compression ring can be installed with either side facing upward.

·

Install the No. 2 compression ring with the code mark shown in the table below facing upward.



Standard Code Mark:
Item Code Mark
(for Euro IV or higher)
Code Mark
(for Euro III)
No. 1 compression ring No mark No mark
No. 2 compression ring T2 2T



e.

Position the piston rings so that the ring ends are as shown in the illustration below.

A164630C01
2.24,1.958 2.24,2.521 true 2.063,1.958 2.063,2.365 2.063,2.365 2.24,2.365 true 5.094,1.948 5.094,2.51 true 1.25,0.094 1.563,0.25 0.313,0.156 10 false *A 4.083,0.094 4.396,0.25 0.313,0.156 10 false *B 2.76,0.656 3.073,0.813 0.313,0.156 10 false *1 4.25,1.99 4.563,2.146 0.313,0.156 10 false *2 1.385,0.615 1.698,0.771 0.313,0.156 10 false *3 2.781,2 3.094,2.156 0.313,0.156 10 false *4 2.156,2.51 2.469,2.667 0.313,0.156 10 false *a 5.625,0.656 5.938,0.813 0.313,0.156 10 false *1 1.406,1.99 1.719,2.146 0.313,0.156 10 false *2 5.604,2.01 5.917,2.167 0.313,0.156 10 false *4 4.229,0.625 4.542,0.781 0.313,0.156 10 false *3 5.021,2.5 5.333,2.656 0.313,0.156 10 false *a
*A for Bank 1 *B for Bank 2
*1 No. 1 Compression Ring *2 No. 2 Compression Ring
*3 Oil Ring Expander *4 Oil Ring Rail
*a Front Mark - -



Hide 13041 8.INSTALL CONNECTING ROD BEARING

a.
A164871C01
2.333,1.521 2.333,1 2.333,1 2.5,1 true 0.635,0.375 0.417,0.667 0.417,0.667 0.25,0.667 true 0.094,0.573 0.406,0.729 0.313,0.156 10 false *a 2.531,0.927 2.844,1.083 0.313,0.156 10 false *a
*a Claw


Align the connecting rod bearing claw with the claw groove of the connecting rod cap.

NOTICE:
·

Clean the contact surface of the connecting rod bearing and connecting rod cap.

·

Do not apply engine oil to the connecting rod bearing and its contact surface.




b.

Align the connecting rod bearing claw with the claw groove of the connecting rod.

NOTICE:
·

Clean the contact surface of the connecting rod bearing and connecting rod.

·

Do not apply engine oil to the connecting rod bearing and its contact surface.




Hide 11711 9.INSTALL CRANKSHAFT BEARING

NOTICE:

Be sure to install the selected crankshaft bearing.


HINT:

Main bearings come in widths of 20.5 mm (0.807 in.) and 22.5 mm (0.886 in.).


Standard Journal Diameter:
Journal Specified Condition
No. 1 and No. 5 22.5 mm (0.886 in.)
No. 2, No. 3 and No. 4 20.5 mm (0.807 in.)


A316808C01
0.969,0.583 1.281,0.74 0.313,0.156 10 false *1 4.854,0.573 5.167,0.729 0.313,0.156 10 false *2 1.375,1.802 1.688,1.958 0.313,0.156 10 false *a 5.292,1.813 5.604,1.969 0.313,0.156 10 false *b
*1 No. 1 and No. 5 Crankshaft Bearings *2 No. 2, No. 3 and No. 4 Crankshaft Bearings
*a 22.5 mm (0.886 in.) *b 20.5 mm (0.807 in.)


a.

Clean each main journal and crankshaft bearing.


b.
A164628

Align the crankshaft bearing claw with the claw groove of the cylinder block sub-assembly, and push in the 5 upper crankshaft bearings.

NOTICE:
·

Clean the contact surface of the crankshaft bearing and cylinder block sub-assembly.

·

Do not apply engine oil to the crankshaft bearing and its contact surface.

·

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.




c.
A164629

Align the crankshaft bearing claw with the claw groove of the crankshaft bearing cap, and push in the 5 lower crankshaft bearings.

NOTICE:
·

Clean the contact surface of the crankshaft bearing and crankshaft bearing cap.

·

Do not apply engine oil to the crankshaft bearing and its contact surface.



HINT:

The number marked on each crankshaft bearing cap indicates the installation position.



Hide 13411 10.INSTALL CRANKSHAFT

NOTICE:

Clean the contact surface of each main journal and crank pin.


a.
A164570

Apply new engine oil to the upper crankshaft bearing and install the crankshaft on the cylinder block sub-assembly.


b.
A164600C01
1.219,2 1.219,1.083 true 1.219,1.833 1.969,1.833 1.969,1.833 1.969,1.417 true 1.135,2.01 1.51,2.177 0.375,0.167 10 true *a
*a Oil Groove


Push the crankshaft toward the rear thrust direction to create clearance, and install a thrust washer to the No. 3 journal position with the oil groove facing the front of the engine.


c.

Push the crankshaft toward the forward thrust direction to create clearance, and install a thrust washer to the No. 3 journal position with the oil groove facing the rear of the engine.


d.
A164632C01
0.979,0.948 1.208,1.146 0.229,0.198 10 false .
V100136

Front


Examine the front marks and numbers and install the crankshaft bearing caps on the cylinder block sub-assembly.

NOTICE:

Do not turn the crankshaft.



e.

Apply a light coat of engine oil to the threads of the crankshaft bearing cap set bolts.


f.

Temporarily install the crankshaft bearing cap set bolts to the A or B position.

A326451C01
1.031,0.438 1.833,0.667 1.833,0.667 2,0.667 true 2.031,0.583 2.344,0.74 0.313,0.156 10 false *1 0.938,0.677 1.25,0.833 0.313,0.156 10 false *a 5.458,1.167 5.771,1.323 0.313,0.156 10 false *b 5.458,2.146 5.771,2.302 0.313,0.156 10 false *c 6.354,0.813 6.667,0.969 0.313,0.156 10 false *d 6.292,1.792 6.604,1.948 0.313,0.156 10 false *e
*1 Spacer - -
*a 8 mm (0.315 in.) *b 106 mm (4.17 in.)
*c 90.5 mm (3.56 in.) *d 11 mm (0.433 in.)
*e 10 mm (0.394 in.) - -
V100135

Bolt A
V100136

Bolt B


HINT:

In place of cylinder block stiffening plates, install 8 mm (0.315 in.) thick spacers to the crankshaft bearing cap set bolts.



g.

Uniformly tighten the 2 crankshaft bearing cap set bolts for each bearing cap in several passes to ensure a proper fit.

NOTICE:

Do not tap the bearing cap with a plastic-faced hammer.



h.

Remove the crankshaft bearing cap set bolts and spacers.


i.
A164799C01
2.25,0.167 2.417,0.167 2.417,0.167 2.719,0.552 true 2.25,2 2.417,2 2.417,2 2.719,1.615 true 2.083,0.063 2.26,0.26 0.177,0.198 10 true *a 2.094,1.896 2.271,2.104 0.177,0.208 10 true *a
*a Front Mark


Set the 2 cylinder block stiffening plates on the cylinder block sub-assembly.

HINT:

Make sure the arrows on the stiffening plates face the engine front.



j.

Step 1:

HINT:
·

The crankshaft bearing cap set bolts are tightened in 3 progressive steps.

·

If any crankshaft bearing cap set bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the heads of the 20 crankshaft bearing cap set bolts.


ii.
A326452C01
0.365,0.156 0.656,0.323 0.292,0.167 10 true 20 1.063,0.156 1.354,0.323 0.292,0.167 10 true 16 1.656,0.156 1.948,0.323 0.292,0.167 10 true 12 2.271,0.156 2.563,0.323 0.292,0.167 10 true 13 2.979,0.156 3.271,0.323 0.292,0.167 10 true 17 0.75,0.698 1.042,0.865 0.292,0.167 10 true 10 1.458,0.698 1.625,0.865 0.167,0.167 10 true 6 2.063,0.698 2.229,0.865 0.167,0.167 10 true 2 2.688,0.698 2.854,0.865 0.167,0.167 10 true 3 3.229,0.75 3.396,0.917 0.167,0.167 10 true 7 0.771,1.323 0.938,1.49 0.167,0.167 10 true 9 1.469,1.323 1.635,1.49 0.167,0.167 10 true 5 2.073,1.323 2.24,1.49 0.167,0.167 10 true 1 2.688,1.313 2.854,1.479 0.167,0.167 10 true 4 3.24,1.542 3.406,1.708 0.167,0.167 10 true 8 2.979,1.854 3.271,2.021 0.292,0.167 10 true 18 2.271,1.865 2.563,2.031 0.292,0.167 10 true 14 1.656,1.854 1.948,2.021 0.292,0.167 10 true 11 1.042,1.854 1.333,2.021 0.292,0.167 10 true 15 0.344,1.865 0.635,2.031 0.292,0.167 10 true 19
V100135

Bolt A
V100136

Bolt B


Install the 20 crankshaft bearing cap set bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.

Torque:
for bolt A : 35 N*m (357 kgf*cm, 26 ft.*lbf)
for bolt B : 60 N*m (612 kgf*cm, 44 ft.*lbf)



k.

Step 2:

i.
A326453C01
0.833,4.25 0.833,4.083 0.833,4.083 1.156,3.448 true 0.75,4.229 1.063,4.385 0.313,0.156 10 false *a 0.219,3.688 0.531,3.844 0.313,0.156 10 false *b 0.833,2.688 1.292,2.885 0.458,0.198 10 false 90° 0.344,0.146 0.563,0.313 0.219,0.167 10 true 20 1.042,0.146 1.26,0.313 0.219,0.167 10 true 16 1.677,0.146 1.896,0.313 0.219,0.167 10 true 12 2.292,0.146 2.51,0.313 0.219,0.167 10 true 13 3.01,0.146 3.229,0.313 0.219,0.167 10 true 17 0.74,0.698 0.958,0.865 0.219,0.167 10 true 10 1.458,0.698 1.677,0.865 0.219,0.167 10 true 6 2.083,0.698 2.302,0.865 0.219,0.167 10 true 2 2.719,0.708 2.938,0.875 0.219,0.167 10 true 3 3.26,0.76 3.417,0.958 0.156,0.198 10 true 7 3.25,1.552 3.406,1.75 0.156,0.198 10 true 8 2.729,1.344 2.948,1.51 0.219,0.167 10 true 4 2.104,1.344 2.323,1.51 0.219,0.167 10 true 1 1.479,1.344 1.698,1.51 0.219,0.167 10 true 5 0.76,1.344 0.979,1.51 0.219,0.167 10 true 9 0.333,1.896 0.552,2.063 0.219,0.167 10 true 19 1.042,1.906 1.26,2.073 0.219,0.167 10 true 15 1.667,1.906 1.885,2.073 0.219,0.167 10 true 11 2.292,1.906 2.51,2.073 0.219,0.167 10 true 14 3.01,1.896 3.229,2.063 0.219,0.167 10 true 18
*a Painted Mark
*b Front
V100135

Bolt A
V100136

Bolt B


Mark the front side of the crankshaft bearing cap set bolts A and B with paint.


ii.

Tighten the crankshaft bearing cap set bolts A and B 90° in the sequence as shown in the illustration.



l.

Step 3:

i.
A326454C01
0.917,2.5 1.083,2.5 1.083,2.5 1.573,2.896 true 0.76,2.396 1.073,2.552 0.313,0.156 10 false *a 0.25,3.698 0.563,3.854 0.313,0.156 10 false *b 2.208,2.625 2.667,2.823 0.458,0.198 10 false 90° 0.75,0.698 0.979,0.896 0.229,0.198 10 true 10 1.469,0.708 1.698,0.906 0.229,0.198 10 true 6 2.094,0.698 2.323,0.896 0.229,0.198 10 true 2 2.719,0.698 2.948,0.896 0.229,0.198 10 true 3 3.229,0.76 3.375,0.969 0.146,0.208 10 true 7 3.24,1.563 3.385,1.771 0.146,0.208 10 true 8 2.719,1.344 2.865,1.552 0.146,0.208 10 true 4 2.104,1.344 2.25,1.552 0.146,0.208 10 true 1 1.479,1.344 1.625,1.552 0.146,0.208 10 true 5 0.771,1.333 0.917,1.542 0.146,0.208 10 true 9
*a Painted Mark
*b Front
V100135

Bolt A


Tighten the crankshaft bearing cap set bolts A another 90° in the sequence as shown in the illustration.


ii.
A170349C01
2.313,1.146 2.667,0.667 2.667,0.667 2.833,0.667 true 2.865,0.573 3.177,0.729 0.313,0.156 10 false *a 0.458,1.406 0.771,1.563 0.313,0.156 10 false *b
*a Painted Mark
*b Front


Check that the painted marks of bolt A are now at a 180° angle to the front.


iii.
A170350C02
1.792,0.604 2.417,0.25 2.417,0.25 2.583,0.25 true 2.615,0.167 2.927,0.323 0.313,0.156 10 false *a 0.458,1.406 0.771,1.563 0.313,0.156 10 false *b
*a Painted Mark
*b Front


Check that the painted marks of bolt B are now at a 90° angle to the front.

NOTICE:

Do not turn the crankshaft.




m.

Step 4:

i.
A164796N02
0.667,0.146 0.979,0.344 0.313,0.198 10 true 10 1.365,0.135 1.677,0.333 0.313,0.198 10 true 6 2,0.135 2.313,0.333 0.313,0.198 10 true 2 2.615,0.125 2.927,0.323 0.313,0.198 10 true 3 3.167,0.083 3.292,0.26 0.125,0.177 10 true 7 0.667,1.875 0.979,2.073 0.313,0.198 10 true 9 1.365,1.865 1.677,2.063 0.313,0.198 10 true 5 1.979,1.865 2.292,2.063 0.313,0.198 10 true 1 2.604,1.875 2.917,2.073 0.313,0.198 10 true 4 3.219,1.927 3.354,2.135 0.135,0.208 10 true 8

Using several steps, install the 10 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)



n.

Check that the crankshaft turns smoothly.


Hide 12.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons, and the surfaces of the connecting rod bearings.


b.

Check the positions of the piston ring ends.

A164630C01
2.24,1.958 2.24,2.521 true 2.063,1.958 2.063,2.365 2.063,2.365 2.24,2.365 true 5.094,1.948 5.094,2.51 true 1.25,0.094 1.563,0.25 0.313,0.156 10 false *A 4.083,0.094 4.396,0.25 0.313,0.156 10 false *B 2.76,0.656 3.073,0.813 0.313,0.156 10 false *1 4.25,1.99 4.563,2.146 0.313,0.156 10 false *2 1.385,0.615 1.698,0.771 0.313,0.156 10 false *3 2.781,2 3.094,2.156 0.313,0.156 10 false *4 2.156,2.51 2.469,2.667 0.313,0.156 10 false *a 5.625,0.656 5.938,0.813 0.313,0.156 10 false *1 1.406,1.99 1.719,2.146 0.313,0.156 10 false *2 5.604,2.01 5.917,2.167 0.313,0.156 10 false *4 4.229,0.625 4.542,0.781 0.313,0.156 10 false *3 5.021,2.5 5.333,2.656 0.313,0.156 10 false *a
*A for Bank 1 *B for Bank 2
*1 No. 1 Compression Ring *2 No. 2 Compression Ring
*3 Oil Ring Expander *4 Oil Ring Rail
*a Front Mark - -



c.

Using a hammer handle and piston ring compressor, press a piston and connecting rod assembly into each cylinder with the front mark of the piston facing forward.

A164631C01
3.583,2.917 3.583,3.25 3.583,3.25 3.5,3.25 true 3.5,3.333 3.5,3 true 6.031,2.979 6.5,3.333 6.5,3.333 6.667,3.333 true 3.354,0.917 3.667,1.073 0.313,0.156 10 false *A 6.26,0.917 6.573,1.073 0.313,0.156 10 false *B 3.417,3.333 3.76,3.5 0.344,0.167 10 true *a 4.865,3.229 5.177,3.385 0.313,0.156 10 false *b 6.698,3.24 7.01,3.396 0.313,0.156 10 false *a
*A for Bank 1 *B for Bank 2
*a Front Mark *b Front



d.
A164639C01
0.75,1.167 0.75,1 0.75,1 0.594,0.49 true 2.635,1.219 2.635,0.719 true 0.135,0.115 0.469,0.375 0.333,0.26 10 true *A 1.927,0.115 2.229,0.313 0.302,0.198 10 true *B 0.667,1.167 0.958,1.365 0.292,0.198 10 true *a 0.125,0.781 0.438,0.938 0.313,0.156 10 true *b 2.885,0.958 3.198,1.115 0.313,0.156 10 true *c 2.563,1.198 2.854,1.396 0.292,0.198 10 true *a
*A for Bank 1
*B for Bank 2
*a Protrusion
*b Front
*c Rear


Install the connecting rod cap so that its protrusion is facing the correct direction.

NOTICE:

Match the numbered connecting rod cap with the connecting rod.



e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


f.

Step 1:

i.
A164565

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

HINT:
·

The connecting rod cap bolts are tightened in 2 progressive steps.

·

If any connecting bolt cap bolts is broken or deformed, replace it.





g.

Step 2:

i.

Mark the front side of each connecting rod cap bolt with paint.


ii.
A158686C04
1.167,1.833 1.167,1.667 1.167,1.667 1.521,1.135 true 0.292,1.375 0.604,1.531 0.313,0.156 10 false *a 1.104,1.844 1.417,2 0.313,0.156 10 false *b 1.177,0.396 1.521,0.615 0.344,0.219 10 false 90°
*a Front
*b Painted Mark


Tighten the connecting rod cap bolts 90°.


iii.
A170350C03
1,0.333 1.167,0.333 1.167,0.333 1.792,0.615 true 0.427,1.385 0.74,1.542 0.313,0.156 10 false *a 0.833,0.24 1.146,0.396 0.313,0.156 10 false *b
*a Front
*b Painted Mark


Check that the painted marks are now at a 90° angle to the front.



h.

Check that the crankshaft turns smoothly.


Hide 13.INSPECT CONNECTING ROD THRUST CLEARANCE