Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  P213B  Exhaust Gas Recirculation Throttle Position Control (Range / Performance)  


DESCRIPTION

The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to opening and closing the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance When either condition below is met:
·

When throttle valve (for Bank 1) remains closed despite ECM's signal to open valve

(1 trip detection logic)

·

When throttle valve (for Bank 1) remains open despite ECM's signal to close valve

(1 trip detection logic)


·

Throttle valve (for Bank 1) stuck

·

Throttle valve (for Bank 1) does not move smoothly

·

Open or short in throttle valve (for Bank 1) circuit

·

ECM


Comes on DTC stored
P213B Exhaust Gas Recirculation Throttle Position Control (Range / Performance) When either condition below is met:
·

When throttle valve (for Bank 2) remains closed despite ECM's signal to open valve

(1 trip detection logic)

·

When throttle valve (for Bank 2) remains open despite ECM's signal to close valve

(1 trip detection logic)


·

Throttle valve (for Bank 2) stuck

·

Throttle valve (for Bank 2) does not move smoothly

·

Open or short in throttle valve (for Bank 2) circuit

·

ECM


Comes on DTC stored

Reference
Condition Throttle Valve Position
Moment when accelerator pedal is further depressed or released at 3000 rpm Opening angle varies smoothly

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0488 Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.
P213B

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and the ECM illuminates the MIL.

A128641E03
0.293,5.431 1.684,5.799 1.392,0.368 10 Duty Ratio Malfunction Counter 0.137,0.027 1.921,0.236 1.784,0.209 10 Malfunction Detection: 0.293,1.239 1.703,1.607 1.41,0.368 10 Throttle Valve Target Opening Angle 0.293,2.707 1.767,3.108 1.474,0.4 10 Throttle Valve Actual Opening Angle 0.949,4.117 1.685,4.333 0.736,0.216 10 Duty Ratio 4.797,1.709 5.39,1.91 0.593,0.201 10 Normal 4.797,2.475 5.547,2.676 0.751,0.201 10 Abnormal 4.797,3.98 5.39,4.182 0.593,0.201 10 Normal 4.797,3.215 5.547,3.416 0.751,0.201 10 Abnormal 5.95,0.557 6.401,0.758 0.45,0.201 10 Open 5.95,1.306 6.43,1.507 0.48,0.201 10 Close 5.95,2.017 6.401,2.219 0.45,0.201 10 Open 5.95,2.774 6.43,2.976 0.48,0.201 10 Close 5.95,3.516 6.465,3.72 0.514,0.204 10 100% 5.95,4.28 6.292,4.481 0.342,0.201 10 0% 3.368,5.26 4.789,5.467 1.421,0.208 10 Detect P0488, P213B 5.348,5.238 6.143,5.449 0.795,0.212 10 Threshold 3.509,6.268 3.92,6.471 0.411,0.204 10 Time 4.614,2.111 4.74,1.795 false 4.614,2.87 4.74,2.554 false 4.614,3.616 4.74,3.3 false 4.74,4.076 4.614,3.76 false 5.347,5.23 5.165,5.009 false 3.333,5.35 3.096,5.176 false

WIRING DIAGRAM

for RHD
A403500E03
0.688,4.25 1.76,4.448 1.073,0.198 10 false Battery 0.552,3.438 1.625,3.635 1.073,0.198 10 false FL MAIN 1.042,2.823 2.115,3.021 1.073,0.198 10 false EFI MAIN2 1.063,0.906 2.135,1.104 1.073,0.198 10 false EFI MAIN 2.271,1.677 2.802,1.875 0.531,0.198 10 false MAIN 2.229,3.583 2.76,3.781 0.531,0.198 10 false MAIN2 2.802,0.656 2.958,0.854 0.156,0.198 10 false 3 2.01,0.656 2.167,0.854 0.156,0.198 10 false 5 2.792,1.177 2.948,1.375 0.156,0.198 10 false 1 2.01,1.188 2.167,1.385 0.156,0.198 10 false 2 2.781,3.083 2.938,3.281 0.156,0.198 10 false 1 2.781,2.563 2.938,2.76 0.156,0.198 10 false 3 2.021,3.094 2.177,3.292 0.156,0.198 10 false 2 2.031,2.573 2.188,2.771 0.156,0.198 10 false 5 4,0.771 4.531,0.969 0.531,0.198 10 false VCR 4,2.667 4.531,2.865 0.531,0.198 10 false VCR 3.781,2.552 3.938,2.75 0.156,0.198 10 false 2 3.781,0.656 3.938,0.854 0.156,0.198 10 false 2 5.198,0.667 5.354,0.865 0.156,0.198 10 false 1 5.208,2.552 5.365,2.75 0.156,0.198 10 false 1 5.219,2.938 5.375,3.135 0.156,0.198 10 false 3 5.198,1.083 5.354,1.281 0.156,0.198 10 false 3 4.729,0.802 5.26,1 0.531,0.198 10 false VTAR 4.74,2.667 5.271,2.865 0.531,0.198 10 false VTAR 4.896,3.052 5.156,3.24 0.26,0.188 10 false E2 4.813,1.208 5.135,1.396 0.323,0.188 10 false E2R 5.854,0.802 6.177,0.99 0.323,0.188 10 false C39 5.865,2.667 6.188,2.854 0.323,0.188 10 false C39 5.896,4.479 6.219,4.667 0.323,0.188 10 false A29 5.906,4.271 6.229,4.458 0.323,0.188 10 false 44 5.896,2.458 6.219,2.646 0.323,0.188 10 false 84 5.896,0.594 6.219,0.781 0.323,0.188 10 false 42 6.24,0.802 6.771,1 0.531,0.198 10 false LUSL 6.24,2.667 6.771,2.865 0.531,0.198 10 false LUS2 6.25,4.5 6.781,4.698 0.531,0.198 10 false MREL 6.427,5.25 6.958,5.448 0.531,0.198 10 false ECM 3.458,1.781 5.625,2 2.167,0.219 10 false Throttle Control Motor (for Bank 1) 3.469,1.594 3.792,1.781 0.323,0.188 10 false C58 3.406,3.563 5.573,3.781 2.167,0.219 10 false Throttle Control Motor (for Bank 2) 3.406,3.385 3.729,3.573 0.323,0.188 10 false C61

for LHD
A403500E02
0.688,4.25 1.76,4.448 1.073,0.198 10 false Battery 0.552,3.438 1.625,3.635 1.073,0.198 10 false FL MAIN 1.042,2.823 2.115,3.021 1.073,0.198 10 false EFI MAIN2 1.063,0.906 2.135,1.104 1.073,0.198 10 false EFI MAIN 2.271,1.677 2.802,1.875 0.531,0.198 10 false MAIN 2.229,3.583 2.76,3.781 0.531,0.198 10 false MAIN2 2.802,0.656 2.958,0.854 0.156,0.198 10 false 3 2.01,0.656 2.167,0.854 0.156,0.198 10 false 5 2.792,1.177 2.948,1.375 0.156,0.198 10 false 1 2.01,1.188 2.167,1.385 0.156,0.198 10 false 2 2.781,3.083 2.938,3.281 0.156,0.198 10 false 1 2.781,2.563 2.938,2.76 0.156,0.198 10 false 3 2.021,3.094 2.177,3.292 0.156,0.198 10 false 2 2.031,2.573 2.188,2.771 0.156,0.198 10 false 5 4,0.771 4.531,0.969 0.531,0.198 10 false VCR 4,2.667 4.531,2.865 0.531,0.198 10 false VCR 3.781,2.552 3.938,2.75 0.156,0.198 10 false 2 3.781,0.656 3.938,0.854 0.156,0.198 10 false 2 5.198,0.667 5.354,0.865 0.156,0.198 10 false 1 5.208,2.552 5.365,2.75 0.156,0.198 10 false 1 5.219,2.938 5.375,3.135 0.156,0.198 10 false 3 5.198,1.083 5.354,1.281 0.156,0.198 10 false 3 4.729,0.802 5.26,1 0.531,0.198 10 false VTAR 4.74,2.667 5.271,2.865 0.531,0.198 10 false VTAR 4.896,3.052 5.156,3.24 0.26,0.188 10 false E2 4.813,1.208 5.135,1.396 0.323,0.188 10 false E2R 5.854,0.802 6.177,0.99 0.323,0.188 10 false C39 5.865,2.667 6.188,2.854 0.323,0.188 10 false C39 5.896,4.479 6.219,4.667 0.323,0.188 10 false I84 5.906,4.271 6.229,4.458 0.323,0.188 10 false 44 5.896,2.458 6.219,2.646 0.323,0.188 10 false 84 5.896,0.594 6.219,0.781 0.323,0.188 10 false 42 6.24,0.802 6.771,1 0.531,0.198 10 false LUSL 6.24,2.667 6.771,2.865 0.531,0.198 10 false LUS2 6.25,4.5 6.781,4.698 0.531,0.198 10 false MREL 6.427,5.25 6.958,5.448 0.531,0.198 10 false ECM 3.458,1.781 5.625,2 2.167,0.219 10 false Throttle Control Motor (for Bank 1) 3.469,1.594 3.792,1.781 0.323,0.188 10 false C58 3.406,3.563 5.573,3.781 2.167,0.219 10 false Throttle Control Motor (for Bank 2) 3.406,3.385 3.729,3.573 0.323,0.188 10 false C61

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

After warming up the engine, DTC P0488 and P213B can be set if 1 second or more passes after quickly accelerating the engine from idling.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Active Test / Diesel Throttle Target Angle or Diesel Throttle Target Angle #2.

Powertrain > Engine and ECT > Active Test
Tester Display
Diesel Throttle Target Angle
50004 61 239
Powertrain > Engine and ECT > Active Test
Tester Display
Diesel Throttle Target Angle #2
50004 61 240

d.

While continuously changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that "Actual Throttle Position" or "Actual Throttle Position #2" smoothly changes to the set opening amount.

OK:

Value smoothly changes to set opening amount.



Result:
Proceed to
OK
NG



OK

2.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)

NG

8.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)
2.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
a.

Visually check for deposits in the diesel throttle body assembly. If there are deposits, clean the diesel throttle body assembly.


Result:
Proceed to
NEXT



NEXT

3.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
3.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Active Test / Diesel Throttle Target Angle or Diesel Throttle Target Angle #2.

Powertrain > Engine and ECT > Active Test
Tester Display
Diesel Throttle Target Angle
50004 61 239
Powertrain > Engine and ECT > Active Test
Tester Display
Diesel Throttle Target Angle #2
50004 61 240

d.

While continuously changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that "Actual Throttle Position" or "Actual Throttle Position #2" smoothly changes to the set opening amount.

OK:

Value smoothly changes to set opening amount.



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

b.

Turn the ignition switch off and wait for 30 seconds.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Start the engine.


f.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

h.

Read the DTCs.

Result:
Display Proceed to
P0488 or P213B is output A
No DTC is output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

c.

Turn the ignition switch off and wait for 30 seconds.


d.

Start the engine.


e.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0488 and P213B.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.



Result:
Proceed to
NEXT



NEXT

END

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
·

When DTC P0488 is output

Replace the diesel throttle body assembly (for bank 1).

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL

·

When DTC P213B is output

Replace the diesel throttle body assembly (for bank 2).

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)
a.
A129055C27
0.302,0.875 0.802,1.188 0.5,0.313 0.302,1.406 0.802,1.719 0.5,0.313 1.708,1.479 1.708,1.927 true 0.094,0.104 1.385,0.271 1.292,0.167 10 false *a 0.427,0.948 0.708,1.115 0.281,0.167 10 false C58 1.573,1.938 1.958,2.125 0.385,0.188 10 false VCR 0.427,1.479 0.708,1.646 0.281,0.167 10 false C61 0.844,0.75 1.125,0.917 0.281,0.167 10 false *A 0.833,1.313 1.115,1.479 0.281,0.167 10 false *B
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Throttle Control Motor)


Disconnect the throttle control motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
for Bank 1
Tester Connection Switch Condition Specified Condition
C58-2 (VCR) - Body ground Ignition switch ON 11 to 14 V

for Bank 2
Tester Connection Switch Condition Specified Condition
C61-2 (VCR) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the throttle control motor connector.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - INTEGRATION RELAY)
9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle control motor connector.


b.

Remove the MAIN relay and MAIN2 relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for Bank 1
Tester Connection Condition Specified Condition
C58-2 (VCR) - MAIN relay terminal 3 Always Below 1 Ω
C58-2 (VCR) or MAIN relay terminal 3 - Body ground Always 10 kΩ or higher

for Bank 2
Tester Connection Condition Specified Condition
C61-2 (VCR) - MAIN2 relay terminal 3 Always Below 1 Ω
C61-2 (VCR) or MAIN2 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle control motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for Bank 1
Tester Connection Condition Specified Condition
C58-1 (VTAR) - C39-42 (LUSL) Always Below 1 Ω
C58-3 (E2R) - Body ground Always Below 1 Ω
C58-1 (VTAR) or C39-42 (LUSL) - Body ground Always 10 kΩ or higher

for Bank 2
Tester Connection Condition Specified Condition
C61-1 (VTAR) - C39-84 (LUS2) Always Below 1 Ω
C61-3 (E2) - Body ground Always Below 1 Ω
C61-1 (VTAR) or C39-84 (LUS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - INTEGRATION RELAY)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED