The intake air temperature sensor is built into the mass air flow (MAF) meter and senses the intake air temperature.
A thermistor built into the sensor changes its resistance value according to the intake air temperature.
The lower the intake air temperature, the greater the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (see Fig. 1).
The intake air temperature sensor is connected to the ECM.
The 5 V power source voltage in the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.
The resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with changes in the intake air temperature, the potential at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0110 | Intake Air Temperature Circuit | Open or short in intake air temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic) |
·
Open or short in intake air temperature (IAT) sensor circuit
·
IAT sensor (built into mass air flow meter)
·
ECM |
Comes on | DTC stored |
| P0112 | Intake Air Temperature Circuit Low Input | Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic) |
·
Open in IAT sensor circuit
·
IAT sensor (built into mass air flow meter)
·
ECM |
Comes on | DTC stored |
| P0113 | Intake Air Temperature Circuit High Input | Open in IAT sensor circuit for 0.5 seconds (1 trip detection logic) |
·
Open in IAT sensor circuit
·
IAT sensor (built into mass air flow meter)
·
ECM |
Comes on | DTC stored |
When DTC P0110, P0112 or P0113 is detected, check the intake air temperature by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Intake Air.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch ON and turn the GTS ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
| Tester Display |
|---|
| Intake Air |
Read the value.
Same as actual intake air temperature.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (same as actual intake air temperature) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or more.
A
B
C
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
| *1 | Mass Air Flow Meter |
| *2 | ECM |
| *a | Front view of wire harness connector (to Mass Air Flow Meter) |
Disconnect the mass air flow meter connector.
Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.
Connect the GTS to the DLC3.
Turn the ignition switch ON and turn the GTS ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
| Tester Display |
|---|
| Intake Air |
Read the value.
140°C (284°F) or higher
| Proceed to |
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Mass Air Flow Meter) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-4 (THA) - C39-71 (THA) | Always | Below 1 Ω |
| C41-5 (E2) - C39-75 (E2) | Always | Below 1 Ω |
| Proceed to |
| OK |
| NG |
OK
NG
| *1 | Mass Air Flow Meter |
| *2 | ECM |
Disconnect the mass air flow meter connector.
Connect the GTS to the DLC3.
Turn the ignition switch ON and turn the GTS ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
| Tester Display |
|---|
| Intake Air |
Read the value.
-40°C (-40°F)
| Proceed to |
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Mass Air Flow Meter) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-4 (THA) or C39-71 (THA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG