The throttle position sensor is mounted on the diesel throttle body and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.
When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.
The ECM determines the vehicle's driving conditions from the signals input to its VLU terminal. The data is one of the inputs used for EGR control, etc.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0122 | Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input | Throttle position sensor (for Bank 1) output (VLU) is less than 0.2 V (1 trip detection logic) |
·
Throttle position sensor (for Bank 1)
·
Open or short in VLU circuit
·
Open in VC circuit
·
ECM |
Comes on | DTC stored |
| P0123 | Throttle / Pedal Position Sensor / Switch "A" Circuit High Input | Throttle position sensor (for Bank 1) output (VLU) is more than 4.8 V (1 trip detection logic) |
·
Throttle position sensor (for Bank 1)
·
Open in E2 circuit
·
VC and VLU circuits are short-circuited
·
ECM |
Comes on | DTC stored |
| P0222 | Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input | Throttle position sensor (for Bank 2) output (VLU2) is less than 0.2 V (1 trip detection logic) |
·
Throttle position sensor (for Bank 2)
·
Open or short in VLU2 circuit
·
Open in VC circuit
·
ECM |
Comes on | DTC stored |
| P0223 | Throttle / Pedal Position Sensor / Switch "B" Circuit High Input | Throttle position sensor (for Bank 2) output (VLU2) is more than 4.8 V (1 trip detection logic) |
·
Throttle position sensor (for Bank 2)
·
Open in E2 circuit
·
VC and VLU2 circuits are short-circuited
·
ECM |
Comes on | DTC stored |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0122 P0123 P0222 P0223 |
Ignition switch to ON for 3 seconds |
When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *1 | for Bank 1 |
| *2 | for Bank 2 |
| *a | Front view of wire harness connector (to Throttle Position Sensor) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the throttle position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-1 (VC) - C39-91 (VCVL) | Always | Below 1 Ω |
| C50-3 (VTA) - C39-93 (VLU) | Always | Below 1 Ω |
| C50-2 (E2) - C39-92 (EVLU) | Always | Below 1 Ω |
| C50-1 (VC) or C39-91 (VCVL) - Body ground | Always | 10 kΩ or higher |
| C50-3 (VTA) or C39-93 (VLU) - Body ground | Always | 10 kΩ or higher |
| C50-2 (E2) or C39-92 (EVLU) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-1 (VC) - C39-91 (VCVL) | Always | Below 1 Ω |
| C65-3 (VTA) - C39-103 (VLU2) | Always | Below 1 Ω |
| C65-2 (E2) - C39-92 (EVLU) | Always | Below 1 Ω |
| C65-1 (VC) or C39-91 (VCVL) - Body ground | Always | 10 kΩ or higher |
| C65-3 (VTA) or C39-103 (VLU2) - Body ground | Always | 10 kΩ or higher |
| C65-2 (E2) or C39-92 (EVLU) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
| *1 | for Bank 1 |
| *2 | for Bank 2 |
| *a | Front view of wire harness connector (to Throttle Position Sensor) |
Disconnect the throttle position sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C50-1 (VC) - C50-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C65-1 (VC) - C65-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
| OK |
| NG |
OK
NG
Replace the diesel throttle body assembly (for Bank 1 or Bank 2).
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL
| Proceed to |
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch ON and turn the GTS ON.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0122, P0123, P0222 and/or P0223 are output | A |
| No DTC is output | B |
A
B