Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

A115899E35
0.766,1.047 1.553,1.426 0.787,0.378 10 from Speed Sensor 1.817,1.96 3.237,2.123 1.42,0.163 10 Skid Control ECU 3.498,1.96 5.333,2.123 1.835,0.163 10 Combination Meter Assembly 3.113,0.599 3.922,0.776 0.809,0.177 10 4-Pulse 5.039,0.599 5.848,0.776 0.809,0.177 10 4-Pulse 6.068,1.841 6.515,2.005 0.448,0.163 10 ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" When one of the following conditions is met:
·

Following conditions (a), (b), (c) and (d) met for 8 seconds or more:

(2 trip detection logic)

(a)

Engine coolant temperature more than 70°C (158°F)

(b)

Engine speed between 1500 rpm and 4000 rpm

(c)

Vehicle running

(d)

No speed signal input to ECM


·

Following conditions (a), (b) and (c) met for 5 seconds or more:

(a)

Vehicle running

(b)

Under fuel-cut operation

(c)

No speed signal is input to ECM



·

Open or short in speed signal circuit

·

Brake actuator assembly

·

Combination meter

·

ECM


Comes on DTC stored

WIRING DIAGRAM

for RHD
A276508E05
0.354,2.844 1.448,3.26 1.094,0.417 10 false Skid Control ECU (Brake Actuator) 2.219,1.708 2.417,1.875 0.198,0.167 10 false 9 3.917,1.708 4.115,1.875 0.198,0.167 10 false 8 5.031,1.719 5.177,1.885 0.146,0.167 10 false 8 5.958,1.385 6.25,1.552 0.292,0.167 10 false 5 V 5.198,1.646 5.542,1.813 0.344,0.167 10 false SPD 5.667,2.635 6.01,2.802 0.344,0.167 10 false A29 5.667,2.833 6.021,3 0.354,0.167 10 false ECM 2.51,2.646 2.844,2.813 0.333,0.167 10 false L25 2.51,2.844 3.719,3.01 1.208,0.167 10 false Combination Meter 1.75,1.708 1.948,1.875 0.198,0.167 10 false 22 0.344,2.656 0.677,2.823 0.333,0.167 10 false A20 3.635,1.708 3.875,1.854 0.24,0.146 10 false +S 2.417,1.708 2.656,1.854 0.24,0.146 10 false SI 1.365,1.813 1.677,2.031 0.313,0.219 10 false SP1

for LHD
A276508E06
0.354,2.844 1.448,3.26 1.094,0.417 10 false Skid Control ECU (Brake Actuator) 2.219,1.708 2.417,1.875 0.198,0.167 10 false 9 3.917,1.708 4.115,1.875 0.198,0.167 10 false 8 5.031,1.719 5.177,1.885 0.146,0.167 10 false 8 5.958,1.385 6.25,1.552 0.292,0.167 10 false 5 V 5.198,1.646 5.542,1.813 0.344,0.167 10 false SPD 5.667,2.635 6.01,2.802 0.344,0.167 10 false I84 5.667,2.833 6.021,3 0.354,0.167 10 false ECM 2.51,2.646 2.844,2.813 0.333,0.167 10 false L25 2.51,2.844 3.719,3.01 1.208,0.167 10 false Combination Meter 1.75,1.708 1.948,1.875 0.198,0.167 10 false 22 0.344,2.656 0.677,2.823 0.333,0.167 10 false A20 3.635,1.708 3.875,1.854 0.24,0.146 10 false +S 2.417,1.708 2.656,1.854 0.24,0.146 10 false SI 1.365,1.813 1.677,2.031 0.313,0.219 10 false SP1

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:

The vehicle speed sensor is operating normally if the speedometer reading is normal.


OK:

The vehicle speed sensor is operating normally.


Result:
Proceed to
OK
NG




OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and start the engine.


c.

Turn the GTS ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
50003 61 316

e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speeds displayed on tester and speedometer display are equal.NG



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for RHD
Tester Connection Condition Specified Condition
L25-8 (+S) - A29-8 (SPD) Always Below 1 Ω
L25-8 (+S) or A29-8 (SPD) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
L25-8 (+S) - I84-8 (SPD) Always Below 1 Ω
L25-8 (+S) or I84-8 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR