Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.08–2022.09
RM25T0E _58 Vehicle Interior _029927 METER / GAUGE / DISPLAY _0137559 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

w/ VSC


The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the brake actuator assembly (skid control ECU) which uses this information to create the vehicle speed signal*. The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the brake actuator assembly (skid control ECU). The pulse signal is created by switching the transistor in the brake actuator assembly (skid control ECU) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the brake actuator assembly (skid control ECU). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*: This vehicle speed signal is created by the brake actuator assembly (skid control ECU). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.



w/o VSC


The vehicle speed signal consists of pulses sent to the combination meter assembly from the speedometer sensor*1 or brake actuator assembly (skid control ECU)*2.

*1: w/ Speedometer Sensor

*2: w/o Speedometer Sensor



WIRING DIAGRAM

E346841E01
4.438,4.135 4.896,4.333 0.458,0.198 10 false L25 4.427,4.344 6.26,4.646 1.833,0.302 10 false Combination Meter Assembly 4.906,3.51 5.365,3.708 0.458,0.198 10 false +S 4.688,3.521 5.146,3.719 0.458,0.198 10 false 8 4.917,1.292 5.375,1.49 0.458,0.198 10 false SI 4.708,1.292 5.167,1.49 0.458,0.198 10 false 9 2.333,2.896 2.792,3.094 0.458,0.198 10 false A42 2.333,3.094 4.021,3.458 1.688,0.365 10 false Brake Actuator Assembly (Skid Control ECU)*3 3.146,2.573 3.604,2.771 0.458,0.198 10 false SP1 3.542,2.406 4,2.604 0.458,0.198 10 false 14 1.625,3.656 2.083,3.854 0.458,0.198 10 false SPD 2.021,3.531 2.479,3.729 0.458,0.198 10 false 5 0.823,3.927 1.281,4.125 0.458,0.198 10 false L9 0.802,4.104 2.375,4.385 1.573,0.281 10 false Clock Assembly 4.5,5.542 4.958,5.74 0.458,0.198 10 false A31 4.51,5.76 6.469,6.042 1.958,0.281 10 false Emission Control ECU*6 4.906,5.292 5.365,5.49 0.458,0.198 10 false SP1 4.688,5.135 5.146,5.333 0.458,0.198 10 false 5 1.094,5.729 2.104,5.917 1.01,0.188 10 false A29*4, I84*5 1.094,5.906 2.104,6.094 1.01,0.188 10 false ECM 1.594,5.313 2.604,5.5 1.01,0.188 10 false SPD 2.031,5.146 3.042,5.333 1.01,0.188 10 false 8 4.625,7.052 5.635,7.24 1.01,0.188 10 false I8 4.604,7.26 6.823,7.583 2.219,0.323 10 false No. 2 4 Wheel Drive Control ECU*7 4.906,6.802 5.365,7 0.458,0.198 10 false SPD 4.708,6.646 5.167,6.844 0.458,0.198 10 false 4 0.188,6.25 1.198,6.438 1.01,0.188 10 false *1: w/o ABS 0.188,6.563 2.823,6.76 2.635,0.198 10 false *4: for 1GR-FE (for RHD), for 1VD-FTV 0.188,6.833 2.823,7.031 2.635,0.198 10 false *5: for 1GR-FE (for LHD) 0.198,7.083 2.833,7.281 2.635,0.198 10 false *6: for 1HZ (w/ EGR System) 0.208,7.344 2.844,7.542 2.635,0.198 10 false *7: w/ Differential Lock 1.031,6.26 2.646,6.438 1.615,0.177 10 false *2: w/ ABS, w/o VSC 2.427,6.26 3.438,6.448 1.01,0.188 10 false *3: w/ VSC 1.135,1.667 1.594,1.865 0.458,0.198 10 false A20 1.125,1.875 2.813,2.24 1.688,0.365 10 false Brake Actuator Assembly (Skid Control ECU)*2 2.01,1.427 2.469,1.625 0.458,0.198 10 false SP1 2.375,1.313 2.833,1.51 0.458,0.198 10 false 22 0.042,0.573 0.5,0.771 0.458,0.198 10 false C96 0.083,0.76 1.771,1.125 1.688,0.365 10 false Speedmeter Sensor*1 0.99,0.313 1.448,0.51 0.458,0.198 10 false SI 1.281,0.198 1.74,0.396 0.458,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

w/o VSC:

If the speedometer operation is not normal, refer to "Speedometer Malfunction".

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction


PROCEDURE

1.CHECK CLOCK ASSEMBLY

*1: for 1GR-FE (for LHD)

*2: for 1GR-FE (for RHD)

*3: for 1VD-FTV

*4: for 1HZ (w/ EGR System)

*5: w/ Differential Lock


a.
E302810C01
1.458,0.208 1.938,0.458 0.479,0.25 0.625,0.563 0.833,0.563 0.833,0.563 1.656,1.146 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.573,0.26 1.885,0.417 0.313,0.156 10 false L25 0.406,0.479 0.719,0.635 0.313,0.156 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the I84*1 or A29*2, *3 ECM connector.


c.

Disconnect the A31 emission control ECU connector.*4


d.

Disconnect the I8 No. 2 4 wheel drive control ECU connector.*5


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L25-8 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK ECM

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CLOCK ASSEMBLY)
2.CHECK ECM
NOTICE:

For vehicles with a 1HZ, proceed to the next step.


*: w/ Differential Lock


a.
E302810C01
1.458,0.208 1.938,0.458 0.479,0.25 0.625,0.563 0.833,0.563 0.833,0.563 1.656,1.146 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.573,0.26 1.885,0.417 0.313,0.156 10 false L25 0.406,0.479 0.719,0.635 0.313,0.156 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the L9 clock assembly connector.


c.

Disconnect the I8 No. 2 4 wheel drive control ECU connector.*


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L25-8 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK EMISSION CONTROL ECU

NG

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
3.CHECK EMISSION CONTROL ECU
NOTICE:

For vehicles without a 1HZ (w/ EGR system), proceed to the next step.


*: w/ Differential Lock


a.
E302810C01
1.458,0.208 1.938,0.458 0.479,0.25 0.625,0.563 0.833,0.563 0.833,0.563 1.656,1.146 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.573,0.26 1.885,0.417 0.313,0.156 10 false L25 0.406,0.479 0.719,0.635 0.313,0.156 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the L9 clock assembly connector.


c.

Disconnect the I8 No. 2 4 wheel drive control ECU connector.*


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L25-8 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 2 4 WHEEL DRIVE CONTROL ECU

NG

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EMISSION CONTROL ECU)
4.CHECK NO. 2 4 WHEEL DRIVE CONTROL ECU
NOTICE:

For vehicles without a differential lock, proceed to the next step.


*1: for 1GR-FE (for LHD)

*2: for 1GR-FE (for RHD)

*3: for 1VD-FTV

*4: for 1HZ (w/ EGR System)


a.
E302810C01
1.458,0.208 1.938,0.458 0.479,0.25 0.625,0.563 0.833,0.563 0.833,0.563 1.656,1.146 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.573,0.26 1.885,0.417 0.313,0.156 10 false L25 0.406,0.479 0.719,0.635 0.313,0.156 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the L9 clock assembly connector.


c.

Disconnect the I84*1 or A29*2, *3 ECM connector.


d.

Disconnect the A31 emission control ECU connector.*4


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L25-8 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK VEHICLE TYPE

NG

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 4 WHEEL DRIVE CONTROL ECU)
5.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ VSC A
w/o VSC B



A

6.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

B

REPLACE COMBINATION METER ASSEMBLY

6.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.
E346842C01
1.438,0.125 1.938,0.365 0.5,0.24 1.01,1.052 0.656,0.229 0.656,0.229 0.865,0.229 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.552,0.167 2.01,0.365 0.458,0.198 10 false A42 0.917,0.135 1.375,0.333 0.458,0.198 10 false SP1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-14 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
7.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E346843C01
1.5,0.24 1.917,0.479 0.417,0.24 1,1.917 1.25,1.917 1.25,1.917 1.542,1.229 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.135,2.406 0.448,2.604 0.313,0.198 10 false *b 1.292,4.146 1.604,4.344 0.313,0.198 10 false A 2.99,3.542 3.302,3.74 0.313,0.198 10 false GND 1.604,0.271 1.917,0.469 0.313,0.198 10 false L25 0.833,1.844 1.146,2.042 0.313,0.198 10 false SI
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Connect an oscilloscope to terminal L25-9 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection L25-9 (SI) - Body ground
Tool Setting 5 V/DIV., 20 ms./DIV.
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CLOCK ASSEMBLY)

*1: for 1GR-FE (for LHD)

*2: for 1GR-FE (for RHD)

*3: for 1VD-FTV

*4: for 1HZ (w/ EGR System)

*5: w/ Differential Lock


a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the L9 clock assembly connector.


c.

Disconnect the I84*1 or A29*2, *3 ECM connector.


d.

Disconnect the A31 emission control ECU connector.*3


e.

Disconnect the I8 No. 2 4 wheel drive control ECU connector.*5


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-8 (+S) - L9-5 (SPD) Always Below 1 Ω
L25-8 (+S) or L9-5 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

*1: for 1GR-FE (for LHD)

*2: for 1GR-FE (for RHD)

*3: for 1VD-FTV

*4: w/ Differential Lock


a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the L9 clock assembly connector.


c.

Disconnect the I84*1 or A29*2, *3 ECM connector.


d.

Disconnect the I8 No. 2 4 wheel drive control ECU connector.*4


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE (for LHD)
Tester Connection Condition Specified Condition
L25-8 (+S) - I84-8 (SPD) Always Below 1 Ω
L25-8 (+S) or I84-8 (SPD) - Body ground Always 10 kΩ or higher

for 1GR-FE (for RHD), 1VD-FTV
Tester Connection Condition Specified Condition
L25-8 (+S) - A29-8 (SPD) Always Below 1 Ω
L25-8 (+S) or A29-8 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EMISSION CONTROL ECU)

*: w/ Differential Lock


a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the L9 clock assembly connector.


c.

Disconnect the A31 emission control ECU connector.


d.

Disconnect the I8 No. 2 4 wheel drive control ECU connector.*


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-8 (+S) - A31-5 (SP1) Always Below 1 Ω
L25-8 (+S) or A31-5 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 4 WHEEL DRIVE CONTROL ECU)

*1: for 1GR-FE (for LHD)

*2: for 1GR-FE (for RHD)

*3: for 1VD-FTV

*4: for 1HZ (w/ EGR System)

*5: w/ Differential Lock


a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the L9 clock assembly connector.


c.

Disconnect the I84*1 or A29*2, *3 ECM connector.


d.

Disconnect the A31 emission control ECU connector.*4


e.

Disconnect the I8 No. 2 4 wheel drive control ECU connector.*5


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-8 (+S) - I8-4 (SPD) Always Below 1 Ω
L25-8 (+S) or I8-4 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the A42 brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-9 (SI) - A42-14 (SP1) Always Below 1 Ω
L25-9 (SI) or A42-14 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR