The battery supplies electricity to the ECM even when the ignition switch is in the OFF position. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and sets the DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0560 | System Voltage | Open in ECM back up power source circuit (1 trip detection logic) |
·
Open in back up power source circuit
·
Battery
·
Battery terminals
·
EFI MAIN fuse
·
ECM |
Comes on | DTC stored |
If DTC P0560 is set, the ECM does not store other DTCs or the data stored in the ECM is partly erased.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0560 | Ignition switch to ON for 3 seconds |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the harness and connector between the EFI MAIN fuse and ECM.
Remove the EFI MAIN fuse from the fuse block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI MAIN fuse terminal 2 - A29-20 (BATT) | Always | Below 1 Ω |
| EFI MAIN fuse terminal 2 or A29-20 (BATT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI MAIN fuse terminal 2 - I84-20 (BATT) | Always | Below 1 Ω |
| EFI MAIN fuse terminal 2 or I84-20 (BATT) - Body ground | Always | 10 kΩ or higher |
Check the harness and connector between the EFI MAIN fuse and battery.
Remove the EFI MAIN fuse from the fuse block assembly.
Disconnect the positive battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Battery positive (+) terminal - EFI MAIN fuse terminal 1 | Always | Below 1 Ω |
| Battery positive (+) terminal or EFI MAIN fuse terminal 1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Check that the battery is not depleted.
Battery is not depleted.
| Proceed to |
| OK |
| NG |
OK
NG
Check that the battery terminals are not loose or corroded.
Battery terminals are not loose or corroded.
| Proceed to |
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch ON and turn the GTS ON.
Clear DTCs.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch OFF and turn the GTS OFF.
Start the engine and turn the GTS ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Display (DTC Output) | Proceed to |
|---|---|
| P0560 is output | A |
| No DTC is output | B |
A
B
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK FOR INTERMITTENT PROBLEMS