Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM J

1VD-FTV ENGINE CONTROL  ECD SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the EFI MAIN1 relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A415653E01
6.365,4.771 6.823,4.969 0.458,0.198 10 false ECM 6.219,3.292 6.531,3.49 0.313,0.198 10 false E1 6.208,2.74 6.75,2.948 0.542,0.208 10 false MREL 6.198,2.188 6.74,2.396 0.542,0.208 10 false +B 6.198,0.75 6.74,0.958 0.542,0.208 10 false IGSW 5.865,3.271 6.177,3.469 0.313,0.198 10 false C39 5.906,2.74 6.219,2.938 0.313,0.198 10 false I84 5.542,2.74 5.854,2.938 0.313,0.198 10 false A29 5.542,2.188 5.854,2.385 0.313,0.198 10 false A29 5.542,0.854 5.854,1.052 0.313,0.198 10 false A29 5.906,2.188 6.219,2.385 0.313,0.198 10 false I84 5.896,0.854 6.208,1.052 0.313,0.198 10 false I84 5.917,3.073 6.229,3.271 0.313,0.198 10 false 81 5.833,2.563 6.146,2.76 0.313,0.198 10 false 44*2 5.5,2.563 5.813,2.76 0.313,0.198 10 false 44*1 5.542,1.99 5.854,2.188 0.313,0.198 10 false 2*1 5.875,1.99 6.188,2.188 0.313,0.198 10 false 2*2 5.51,0.667 5.896,0.865 0.385,0.198 10 false 28*1 5.833,0.667 6.219,0.865 0.385,0.198 10 false 28*2 4.875,1.01 5.26,1.208 0.385,0.198 10 false IGN 5.073,0.667 5.229,0.865 0.156,0.198 10 false 2 2.458,0.719 2.615,0.917 0.156,0.198 10 false 5 4.781,0.667 4.938,0.865 0.156,0.198 10 false 1 3.781,0.708 3.938,0.906 0.156,0.198 10 false 6 1.094,1.042 1.521,1.24 0.427,0.198 10 false AM2 5.104,3.917 6.938,4.115 1.833,0.198 10 false to Sensor +B 3.479,4.865 5.313,5.063 1.833,0.198 10 false MAIN 2 3.521,3.104 5.354,3.302 1.833,0.198 10 false MAIN 0.906,4.094 2.74,4.292 1.833,0.198 10 false EFI MAIN 2 0.979,2.385 2.813,2.583 1.833,0.198 10 false EFI MAIN 0.469,4.281 2.302,4.479 1.833,0.198 10 false FL MAIN 0.573,4.885 2.406,5.083 1.833,0.198 10 false Battery 4.104,2.594 4.26,2.792 0.156,0.198 10 false 1 4.104,2.031 4.26,2.229 0.156,0.198 10 false 3 3.115,2.594 3.271,2.792 0.156,0.198 10 false 2 3.125,2.042 3.281,2.24 0.156,0.198 10 false 5 4.125,4.344 4.281,4.542 0.156,0.198 10 false 1 4.104,3.771 4.26,3.969 0.156,0.198 10 false 3 3.135,4.333 3.292,4.531 0.156,0.198 10 false 2 3.146,3.781 3.302,3.979 0.156,0.198 10 false 5 2.594,1.313 4.427,1.51 1.833,0.198 10 false L21 2.594,1.531 4.427,1.729 1.833,0.198 10 false Ignition Switch Assembly 4.448,4.844 6.281,5.042 1.833,0.198 10 false *1: for RHD 4.448,5.156 6.281,5.354 1.833,0.198 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C39-81 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECM (IGSW VOLTAGE)
a.
A311475C12
1.25,0.188 1.667,0.479 0.417,0.292 1.76,2.344 2.177,2.635 0.417,0.292 1.052,2.344 1.469,2.635 0.417,0.292 2.531,1.833 1.99,1.271 false 2.531,4.063 2.24,3.229 false 0.125,0.188 0.438,0.385 0.313,0.198 10 false *a 0.198,2.417 0.51,2.615 0.313,0.198 10 false *b 1.344,0.25 1.802,0.448 0.458,0.198 10 false C39 1.875,2.406 2.333,2.604 0.458,0.198 10 false I84 2.469,1.875 3.313,2.219 0.844,0.344 10 false 81 (E1) 2.448,4.115 3.281,4.51 0.833,0.396 10 false 28 (IGSW) 1.146,2.406 1.604,2.604 0.458,0.198 10 false A29 1.271,2.146 1.729,2.344 0.458,0.198 10 false *A 2.031,2.135 2.49,2.333 0.458,0.198 10 false *B
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to ECM)
*b Front view of wire harness connector
(to ECM)


Disconnect the ECM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
for RHD
Tester Connection Switch Condition Specified Condition
A29-28 (IGSW) - C39-81 (E1) Always 11 to 14 V

for LHD
Tester Connection Switch Condition Specified Condition
I84-28 (IGSW) - C39-81 (E1) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MAIN RELAY (MAIN OR MAIN 2)

NG

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
3.INSPECT MAIN RELAY (MAIN OR MAIN 2)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAIN RELAY - ECM, MAIN 2 RELAY - ECM)

NG

REPLACE MAIN RELAY (MAIN OR MAIN 2)

4.CHECK HARNESS AND CONNECTOR (MAIN RELAY - ECM, MAIN 2 RELAY - ECM)
a.

Disconnect the ECM connectors.


b.

Remove the MAIN or MAIN 2 relay from the engine room R/B assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for RHD
Tester Connection Condition Specified Condition
MAIN relay terminal 3 - A29-2 (+B) Always Below 1 Ω
MAIN relay terminal 1 - A29-44 (MREL) Always Below 1 Ω
MAIN 2 relay terminal 1 - A29-44 (MREL) Always Below 1 Ω
MAIN relay terminal 3 or A29-2 (+B) - Body ground Always 10 kΩ or higher
MAIN relay terminal 1 or A29-44 (MREL) - Body ground Always 10 kΩ or higher
MAIN 2 relay terminal 1 or A29-44 (MREL) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
MAIN relay terminal 3 - I84-2 (+B) Always Below 1 Ω
MAIN relay terminal 1 - I84-44 (MREL) Always Below 1 Ω
MAIN 2 relay terminal 1 - I84-44 (MREL) Always Below 1 Ω
MAIN relay terminal 3 or I84-2 (+B) - Body ground Always 10 kΩ or higher
MAIN relay terminal 1 or I84-44 (MREL) - Body ground Always 10 kΩ or higher
MAIN 2 relay terminal 1 or I84-44 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (MAIN RELAY - BATTERY, MAIN 2 RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAIN RELAY - BATTERY, MAIN 2 RELAY - BATTERY)
a.

Remove the MAIN or MAIN 2 relay from the engine room R/B assembly.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
MAIN relay terminal 5 - Battery positive (+) terminal Always Below 1 Ω
MAIN 2 relay terminal 5 - Battery positive (+) terminal Always Below 1 Ω
MAIN relay terminal 5 - Body ground Always 10 kΩ or higher
MAIN 2 relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MAIN RELAY - BODY GROUND, MAIN 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MAIN RELAY - BODY GROUND, MAIN 2 RELAY - BODY GROUND)
a.

Remove the MAIN or MAIN 2 relay from the engine room R/B assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
MAIN relay terminal 2 - Body ground Always Below 1 Ω
MAIN 2 relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
a.

Disconnect the ignition switch connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for RHD
Tester Connection Condition Specified Condition
L21-6 (IG2) - A29-28 (IGSW) Always Below 1 Ω
L21-6 (IG2) or A29-28 (IGSW) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
L21-6 (IG2) - I84-28 (IGSW) Always Below 1 Ω
L21-6 (IG2) or I84-28 (IGSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH)

NG

REPLACE IGNITION SWITCH ASSEMBLY