Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _128087 PRE-COLLISION _0548646 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U030051  Internal Control Module Software Incompatibility Not Programmed  U030057  Internal Control Module Software Incompatibility Invalid / Incompatible Software Component  


DESCRIPTION

·

The forward recognition camera receives vehicle information (Conv/HV/EV) from the ECM via the CAN communication line.

·

When the forward recognition camera is unable to determine the vehicle information (Conv/HV/EV) from the vehicle information (Conv/HV/EV) sent from the ECM, the forward recognition camera outputs U030051.

·

When the vehicle information (Conv/HV/EV) sent from the ECM does not match the vehicle information stored by the forward recognition camera, the forward recognition camera outputs U030057.


DTC No. Detection Item DTC Detection Condition Trouble Area
U030051 Internal Control Module Software Incompatibility Not Programmed Once 3 seconds elapse after turning the ignition switch to ON, the system is unable to determine the vehicle information (Conv/HV/EV) sent from the ECM and vehicle information (Conv/HV/EV) sent from the forward recognition camera for approximately 3 seconds or more.
·

ECD system

·

Forward recognition camera


U030057 Internal Control Module Software Incompatibility Invalid / Incompatible Software Component Once 3 seconds elapse after turning the ignition switch to ON, the vehicle information (Conv/HV/EV) sent from the ECM does not match the vehicle information stored by the forward recognition camera for approximately 1 second or more.
·

ECD system

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the forward recognition camera is replaced with a new one, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history (RoB) for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>DRIVING ADJUSTMENT


·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC (ECD SYSTEM)
a.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC are not output A
DTC is output B



A

2.CHECK FOR DTC (HEALTH CHECK)

B

2.CHECK FOR DTC (HEALTH CHECK)
a.

Using the GTS, perform the Health Check.


b.

Check for DTCs.

OK:

ECUs other than the forward recognition camera do not output specification information mismatch DTCs related to the ECM.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Collision System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (Conv/HV/EV) Vehicle information (Conv/HV/EV) Unknown, Conv or HV/EV Unknown: Vehicle information not confirmed
Conv: Conventional
HV/EV: HV
-
Vehicle Information (Transmission Type) Vehicle information (transmission type) MT, AT, CVT, MMT, SMT, HV/EV - AT or Unknown Displays the type of transmission -
Body Electrical > Pre-Collision System > Data List
Tester Display
Vehicle Information (Conv/HV/EV)
Vehicle Information (Transmission Type)
50003 432 24,36
HINT:
·

When the specification stored by the forward recognition camera and the vehicle specification do not match, there is a malfunction in the specification information stored by the forward recognition camera. Therefore, replace the forward recognition camera.

·

When the specification stored by the forward recognition camera and the vehicle specification match, an ECM with different specifications may be installed. Therefore, replace the ECM.




Result:
Result Proceed to
Specification stored by the forward recognition camera and vehicle specification do not match A
"Unknown" is displayed
Specification stored by the forward recognition camera and vehicle specification match B



A

REPLACE FORWARD RECOGNITION CAMERA

B