Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.



CHECK FREEZE FRAME DATA WHEN DTC WAS STORED


a.

Freeze Frame Data is stored when a DTC is output.


b.

Once Freeze Frame Data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.


c.

Check the Freeze Frame Data when a DTC is output.

i.

Select a DTC to display the freeze frame data.

Chassis > Brake > Trouble Codes
50001 435

ii.

Check the freeze frame data for the output DTC.

Chassis > Brake
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - Unit Total Distance Traveled unit km / mile - -
Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215
- -
IG1 Voltage Value IG1 terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V -
BS1 Voltage Value +BS terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to battery voltage
HINT:

This is the voltage detected at terminal +BS (which supplies power to each solenoid) of the skid control ECU (brake actuator assembly)


Motor Power Supply Voltage +BM terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to battery voltage
HINT:

This is the voltage detected at terminal +BM (which supplies power to the ABS motor) of the skid control ECU (brake actuator assembly)


FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Master Cylinder Sensor 1 Master cylinder pressure sensor pressure (value detected by ECU) Min.: -1.00 MPa
Max.: 23.99 MPa
Brake pedal released: -1.00 to 0.00 MPa Reading increases when brake pedal is depressed
Master Cylinder Sensor Temperature Master cylinder pressure sensor temperature Min.: -80°C
Max.: 175°C
Displays current master cylinder pressure sensor -
M/C Sensor Grade Master cylinder pressure sensor change (value detected by ECU) Min.: -30 MPa/s
Max.: 225 MPa/s
Brake pedal released or pedal held at constant position: 0 MPa/s When brake pedal is being operated: Changes in proportion with the pedal movement speed
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Steering Angle Value Steering sensor Min.: -3276.8°
Max.: 3276.7°
Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0°
-
MT Voltage Value ABS motor drive voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to battery voltage
HINT:

This is the voltage output (which supplies power to the ABS motor) from the skid control ECU (brake actuator assembly) to the ABS motor relay


Solenoid Power Supply Voltage Solenoid power supply voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to battery voltage
HINT:

This is the voltage output (which supplies power to each solenoid) from the skid control ECU (brake actuator assembly) to the ABS solenoid relay


Engine Revolutions Engine speed Min.: 0 rpm
Max.: 65535 rpm
Engine stopped: 0 rpm When engine speed is constant: No large fluctuations
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%
Max.: 127.5%
Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
Power Train Driving force Powertrain drive torque Min.: -327680 N
Max.: 327670 N
- -
Gear Position Gear position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / 8th / 9th / 10th / P/N / R Actual gear position -
Shift Lever Position Shift lever position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input Actual shift lever position -
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) /
Not defined /
VSC OFF mode (TRC(TRAC) OFF/VSC OFF)
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
Not defined: Not defined
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
FR Target Oil Pressure Front wheel RH target oil pressure Min.: 0.0 Mpa
Max.: 20.0 Mpa
- Different according to target oil pressure of each wheel
FL Target Oil Pressure Front wheel LH target oil pressure Min.: 0.0 Mpa
Max.: 20.0 Mpa
- Different according to target oil pressure of each wheel
RR Target Oil Pressure Rear wheel RH target oil pressure Min.: 0.0 Mpa
Max.: 20.0 Mpa
- Different according to target oil pressure of each wheel
RL Target Oil Pressure Rear wheel LH target oil pressure Min.: 0.0 Mpa
Max.: 20.0 Mpa
- Different according to target oil pressure of each wheel
Vehicle Speed Maximum wheel speed sensor reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Grade Vehicle acceleration Min.: -25.105 m/s2
Max.: 24.908 m/s2
Vehicle stopped: 0 m/s2 During driving: Changes in proportion with vehicle acceleration/deceleration
Vehicle Stop Time from IG ON Time vehicle stopped after ignition switch turned to ON Min.: 0 s
Max.: 1275 s
- -
Travel Distance from IG ON Driving time after ignition switch turned to ON Min.: 0 s
Max.: 1275 s
- -
Elapsed Time Time elapsed after ignition switch turned to ON Min.: 0.00 s
Max.: 100661.760 s
- -
MT2 Ignition switch ON status Min.: 0.0 V
Max.: 25.5 V
- -
IG Switch Ignition switch ON status OFF / ON - -
Stop Light SW Stop light switch assembly (STP2 terminal input) OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:

The brake pedal state is determined using the voltage at terminal STP2


Parking Brake SW Parking brake switch OFF / ON OFF: Parking brake released
ON: Parking brake applied
-
Stop Light Relay Stop light control relay (STP LP relay)
(STP terminal input)
OFF / ON OFF: Stop light control relay (STP LP relay) OFF
ON: Stop light control relay (STP LP relay) ON
HINT:

The stop light state is determined using the voltage at terminal STP


Inspection Mode Inspection mode OFF / ON OFF: Normal mode
ON: Inspection mode
HINT:

Refer to utility for details on how to enter inspection mode*1


TRC(TRAC) Control TRC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Engine Control TRC engine control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Brake Control TRC brake control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel VSC Ctrl Status Front wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel VSC Ctrl Status Front wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel ABS Ctrl Status Front wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel ABS Ctrl Status Front wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
HAB Control High power assist brake status OFF / ON OFF: During not control
ON: During control
-
BA Ctrl Status BA control status OFF / ON OFF: During not control
ON: During control
-
PBA Ctrl Status PBA control status OFF / ON OFF: During not control
ON: During control
-
Stop Light Relay State for ECU Control Stop light control relay (STP LP relay) (value detected by ECU) OFF / ON OFF: Stop light control relay (STP LP relay) not operating
ON: Stop light control relay (STP LP relay) operating
-
Engine Stop by Stop and Start System Engine stopped by stop and start system status (value detected by ECU) OFF / ON - -
Solenoid State for ECU Control ABS solenoid relay status (for ECU control) OFF / ON OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating
-
Motor State for ECU Control ABS motor relay status (for ECU control) OFF / ON OFF: ABS motor relay not operating
ON: ABS motor relay operating
-
Operation History of IG OFF while Vehicle is moving History of ignition switch turned off when vehicle is in motion OFF / ON OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
-
Dealer Mode Dealer Mode (Signal Check mode or Calibration mode) status OFF / ON OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode)
HINT:
·

for details on dealer mode (signal check mode), refer to test mode procedure*2

·

for details on dealer mode (calibration mode), refer to utility*3



Zero Point Memory State of Steering Angle Sensor Steering sensor zero point memorization status Zero point is not memorized / Zero point is memorized -
HINT:

The steering sensor zero point is acquired when the vehicle is being driven in a straight line at a speed of 15 km/h (9 mph) or more for approximately 1 second


TRC(TRAC)/VSC OFF SW VSC OFF switch (CSW terminal input) OFF / ON OFF: VSC OFF switch OFF
ON: VSC OFF switch ON
HINT:

The VSC OFF switch state is determined using the voltage at terminal CSW


FR Speed Open Front speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C050614, C05061F


FL Speed Open Front speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C050014, C05001F


RR Speed Open Rear speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C051214, C05121F


RL Speed Open Rear speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C050C14, C050C1F


EFI Communication Open ECM communication open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related Vehicle Control History (RoB): X2079

·

Related DTC: U010087


Yaw Rate Open Yaw rate sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: U012587


Deceleration Open Acceleration sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: U012587


Steering Open Steering sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: U012687


Master Cylinder Open Master cylinder pressure sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C054031


FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C050614


FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C050014


RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C051214


RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C050C14


M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection Under intermittent / Normal Under intermittent: Noise detected
Normal: Noise not detected
·

After noise occurs, if there is no noise for 5 seconds, it switches from "Under intermittent" to "Normal".

·

Related DTC: C054049


Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C14D71C


EFI Communication Invalid ECM communication invalid detection Under intermittent / Normal Under intermittent: ECM communication invalid state detected
Normal: ECM communication invalid state not detected
·

After ECM communication invalid state occurs, if there no further invalid state occurs, it switches from "Under intermittent" to "Normal".

·

Related Vehicle Control History (RoB): X2079

·

Related DTC: U010087


Master Cylinder Pressure Sensor Power Supply Open Master cylinder pressure sensor power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C054049


Solenoid Power Supply Open Solenoid power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C143A7F


Motor Power Supply Open Motor power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C052F14


Stop Switch Open Momentary interruption (open circuit) status in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".

·

Related DTC: C054017, P057113






CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the Freeze Frame Data.


a.

Clear the DTCs and Freeze Frame Data.

Chassis > Brake > Clear DTCs
50002 435

b.

Press the clear button.