Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  CALIBRATION  


DESCRIPTION


a.

Refer to the table below and then perform the necessary operation according to the part to be replaced in order to perform calibration.

Parts to be Replaced / Operation Necessary Operation
Skid control ECU (brake actuator assembly) Calibration
Yaw rate and acceleration sensor (airbag ECU assembly) Calibration
Wheel alignment adjustment Calibration



UTILITY ITEMS


Utility Items Main Purpose Link
All Readiness Confirm if DTC judgment has been completed. Refer to calibration
Calibration Enter Dealer Mode (Calibration Mode) and clear the memorized steering sensor zero point, yaw rate and acceleration sensor (airbag ECU assembly) zero point and system information, and then perform steering sensor zero point learning, yaw rate and acceleration sensor (airbag ECU assembly) zero point learning and system information memorization. Refer to calibration
Inspection Mode Enter Inspection Mode which prohibits operation of VSC and TRC. (Click here)
Signal Check Enter Dealer Mode (Signal Check Mode) and perform a signal inspection of the vehicle stability control system. (Click here)
Vehicle Control History (RoB) View vehicle control history. (Click here)
Reset Memory Clear the memorized steering sensor zero point and yaw rate and acceleration sensor (airbag ECU assembly) zero point. Refer to calibration


ALL READINESS


HINT:
·

With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.

·

You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Clear the DTCs even if no DTCs are stored.

Chassis > Brake > Clear DTCs
50002 435

b.

Press the DTC clear button.


c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform the DTC judgment driving pattern to run the DTC judgment.

Chassis > Brake > Utility
Tester Display
All Readiness
50005 435 20

f.

Input the DTC to be confirmed.


g.

Check the DTC judgment result.

GTS Display Description
Normal
·

DTC judgment completed

·

System normal


Abnormal
·

DTC judgment completed

·

System abnormal


Incomplete
·

DTC judgment not completed

·

Perform the driving pattern


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

·

Perform the driving pattern



If the judgment result shows Incomplete or N/A, perform the DTC confirmation driving pattern again.



CALIBRATION


NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

·

If the yaw rate and acceleration sensor (airbag ECU assembly) was replaced or reinstalled, perform "Calibration".

·

Perform "Calibration" with the vehicle on a level surface (within 0.25° gradient). Do not vibrate the vehicle or open or close doors during zero point calibration. To avoid vibrations due to idling, do not start the engine.

·

Perform "Calibration" with the tires at the specified air pressures and all 4 wheels in contact with the ground. (Do not perform with the vehicle lifted up or load applied on lift.)



HINT:
·

When entering dealer mode (calibration mode), the skid control ECU communicates with the forward recognition camera to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit dealer mode (calibration mode) within 5 seconds of entering dealer mode (calibration mode).

·

Performing the following procedure will perform the yaw rate and acceleration sensor (airbag ECU assembly) zero point calibration and store system information simultaneously.

·

If yaw rate and acceleration sensor (airbag ECU assembly) and zero point calibration do not complete normally, the slip indicator light illuminates and a DTC is output.



a.

Check that the shift lever is in neutral.


b.

Turn the ignition switch to ON.


c.

Check that the steering wheel is centered.


d.

Switch the skid control ECU (brake actuator assembly) to Calibration using the GTS.

Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554

e.

Check that the ABS warning light and slip indicator light are in dealer mode (calibration mode) display (blinking at 0.25-second intervals).

NOTICE:

When dealer mode (calibration mode) is selected with the parking brake is not applied, the yaw rate and acceleration sensor (airbag ECU assembly) zero point calibration incomplete DTC is stored.


HINT:
·

When "Calibration" completes normally, the ABS warning light and slip indicator light are in dealer mode (calibration mode) display (blinking at 0.25-second intervals).

·

The slip indicator light may illuminate for approximately 7 seconds until "Calibration" completes normally.

·

Do not exit dealer mode (calibration mode) within 5 seconds of entering dealer mode (calibration mode). If dealer mode (calibration mode) is exited within 5 seconds of entering dealer mode (calibration mode), DTC U023A87 may be stored. If DTC U023A87 is output after exiting test mode, enter test mode again, wait at least 5 seconds, then recheck for DTCs.




f.

Turn the ignition switch off.



RESET MEMORY


NOTICE:

After performing "Reset Memory", make sure to perform "Calibration".


a.

Check that the shift lever is in neutral.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Select the skid control ECU (brake actuator assembly) to Reset Memory using the GTS. Enter the following menus: Chassis / Brake / Utility / Reset Memory.

Chassis > Brake > Utility
Tester Display
Reset Memory
50005 435 4560
NOTICE:
·

If the ignition switch is turned to ON for more than 15 seconds with the parking brake applied after the zero point of the yaw rate and acceleration sensor (airbag ECU assembly) has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under these conditions, the skid control ECU (brake actuator assembly) will store the zero point calibration for the acceleration sensor as not being completed. The skid control ECU (brake actuator assembly) will then also indicate this as a malfunction of the vehicle stability control system using the indicator light.

·

When the vehicle is driven with the zero point cleared, the yaw rate and acceleration sensor (airbag ECU assembly) zero point calibration incomplete DTC is stored.




g.

Turn the ignition switch off.