Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2021.12
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DESCRIPTION

The soak timer is built into the ECM. While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM will interpret this as a malfunction, illuminates the MIL and store this DTC.

A353953E26
4.135,0.698 4.75,0.896 0.615,0.198 10 false IGSW 3.969,2.49 4.583,2.688 0.615,0.198 10 false +B, +B2 3.875,0.979 4.521,1.167 0.646,0.188 10 false IGN 3.094,3.76 4.104,3.958 1.01,0.198 10 false EFI MAIN 4.104,3.292 4.719,3.49 0.615,0.198 10 false MREL 2.479,3.188 2.813,3.354 0.333,0.167 10 false EFI 0.625,3.01 1.927,3.229 1.302,0.219 10 false from FL MAIN Fuse 1.677,0.813 2.938,1.052 1.26,0.24 10 false from Ignition Switch 4.906,1.073 5.667,1.427 0.76,0.354 10 false Soak Timer IC 4.958,2.375 5.625,2.729 0.667,0.354 10 false Power Source IC 4.917,3.188 5.677,3.531 0.76,0.344 10 false MAIN Relay Control IC 5.458,4.167 5.917,4.365 0.458,0.198 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2610 ECM / PCM Internal Engine Off Timer Performance ECM internal malfunction (2 trip detection logic). ECM Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 minutes or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2610.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

Powertrain > Engine and ECT > Trouble Codes
50001 61

j.

If no pending DTC is output, the repair has been successfully completed.


Result:
Proceed to
NEXT



NEXT

END