43405 1.INSTALL FRONT AXLE OUTER SHAFT SUB-ASSEMBLY
Hold the front axle outer shaft in a vise and while compressing a new snap ring, install the front axle inner shaft to the front axle outer shaft.
Make sure that the front axle inner shaft cannot be pulled out.
43211R 2.INSTALL STEERING KNUCKLE BUSHING
Using SST and a press, install a new needle roller bearing and new steering knuckle bushing into the steering knuckle spindle.
43411D 3.INSTALL FRONT DRIVE SHAFT TYPE T OIL SEAL
Using SST and a hammer, install a new front drive shaft type T oil seal into the front axle housing assembly.
Coat the seal lip with MP grease.
45611F 4.INSTALL STEERING KNUCKLE ARM BEARING
Using SST and a hammer, carefully install 2 new bearing outer races.
Place MP grease in the palm of your hand.
Pack grease into the steering knuckle arm bearing, continuing until the grease oozes out from the other side.
Do the same around the bearing circumference.
43211A 5.INSTALL STEERING SET STUD BOLT
Degrease and clean the steering knuckle LH bolt hole.
Using an E12 "TORX" socket wrench, install the 4 front axle stud bolts to the steering knuckle LH.
When replacing the steering knuckle stud bolts, replace the installation nuts with the new nuts that are supplied.
Install the steering setting stud bolts with the side coated with sealant on the steering LH side.
|
Steering Knuckle Installation Seat |
After installing the steering setting stud bolts, do not allow sealant on the steering knuckle installation seat.
43212 6.INSTALL STEERING KNUCKLE LH
Place the 2 steering knuckle arm bearings in positions on the steering knuckle and front axle housing.
Install the steering knuckle to the front axle housing assembly.
43204 7.INSTALL STEERING KNUCKLE OIL SEAL SUB-ASSEMBLY
Install a new steering knuckle outer oil seal, new steering knuckle inner oil seal and new steering knuckle oil seal inner ring to the steering knuckle.
43232 8.TEMPORARILY INSTALL STEERING KNUCKLE BEARING CAP
| *a | Wooden Plate |
Using SST and wooden plate, support the upper bearing inner race.
Install the steering knuckle bearing cap over the used No. 1 steering knuckle adjust shim.
Using a hammer, install the bearing cap into the bearing inner race.
45611G 9.TEMPORARILY INSTALL NO. 1 STEERING KNUCKLE ARM
Install a new steering knuckle king pin dust or ring seal to the No.1 steering knuckle arm.
| *a | Wooden Plate |
Using SST and wooden plate, support the lower bearing inner race.
Using a hammer, install the No. 1 steering knuckle arm into the bearing inner race.
Remove SST from the steering knuckle.
45612A 10.TEMPORARILY INSTALL NO. 2 STEERING KNUCKLE ARM
Use the same procedure described for the No. 1 steering knuckle arm.
43232 11.INSTALL STEERING KNUCKLE BEARING CAP
Install the steering knuckle bearing cap with the 2 bolts.
45611G 12.INSTALL NO. 1 STEERING KNUCKLE ARM
Install the No. 1 steering knuckle arm with the 4 cone washers and 4 nuts.
45612A 13.INSTALL NO. 2 STEERING KNUCKLE ARM
Use the same procedure described for the No. 1 steering knuckle arm.
45611F 14.MEASURE BEARINGS PRELOAD
Using a spring tension gauge, measure the preload.
25 to 44 N (3 to 4 kgf, 5.6 to 9.9 lbf)
45611F 15.ADJUST BEARINGS PRELOAD
Remove the steering knuckle bearing cap and No. 1 steering knuckle adjust shim.
Select the No. 1 steering knuckle adjust shim.
| Thickness mm (in.) |
|---|
| 0.1 (0.004) |
| 0.2 (0.008) |
| 0.5 (0.020) |
| 1.0 (0.039) |
Install the steering knuckle bearing cap with the 2 bolts.
43241 16.INSTALL STEERING KNUCKLE OIL SEAL COVER
Install the 2 steering knuckle oil seal covers to the steering knuckle with the 6 bolts.
45047 17.CONNECT TIE ROD END SUB-ASSEMBLY LH
Connect the tie rod end to the No. 1 steering knuckle arm with the nut.
Tighten the nut up to an additional 60° if the holes for the cotter pin are not aligned.
Install a new cotter pin.
18.INSTALL FRONT AXLE SHAFT ASSEMBLY
Position one flat part of the outer shaft upward and install the front axle shaft assembly.
19.PACK STEERING KNUCKLE WITH GREASE
| *a | Molybdenum Disulfide Lithium Base Grease, NLGI No. 2 |
Pack molybdenum disulfide lithium base grease, NLGI No. 2 into the steering knuckle to about 3 fourths of the steering knuckle.
43401 20.INSTALL STEERING KNUCKLE SPINDLE SUB-ASSEMBLY
Place a new knuckle spindle gasket in position on the steering knuckle and install the knuckle spindle.
Place the front disc brake dust cover, new front axle hub dust seal and a new knuckle spindle oil retainer gasket on the steering knuckle spindle.
Install the 8 bolts.
21.CONNECT FRONT SPEED SENSOR LH (w/ ABS)
Connect the front speed sensor LH to the steering knuckle with the bolt.
43502C 22.INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH
23.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
24.CHECK ABS SPEED SENSOR SIGNAL (w/ VSC)
w/ Pre-collision System:
w/o Pre-collision System:
25.CHECK ABS SPEED SENSOR SIGNAL (w/o VSC)