Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0556385 CAN COMMUNICATION SYSTEM(w/ Pre-collision System) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Pre-collision System)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly CAN main wire or connector

·

Combination meter assembly



WIRING DIAGRAM

C363545E05
5.135,4.104 7.052,4.531 1.917,0.427 10 false Combination Meter Assembly 0.417,1.583 2.333,2.01 1.917,0.427 10 false I134 0.417,1.75 2.083,2.229 1.667,0.479 10 false No. 7 Global CAN Junction Connector 1.594,1.073 3.51,1.5 1.917,0.427 10 false 13 1.604,0.563 3.521,0.99 1.917,0.427 10 false 2 5.271,0.458 6.042,0.885 0.771,0.427 10 false 13 5.635,0.573 6.406,1 0.771,0.427 10 false CANH 5.656,1.333 6.427,1.76 0.771,0.427 10 false CANL 5.677,1.917 6.448,2.344 0.771,0.427 10 false B 5.667,2.625 6.438,3.052 0.771,0.427 10 false B 5.677,3.323 6.448,3.75 0.771,0.427 10 false ES 5.25,3.333 6.021,3.76 0.771,0.427 10 false L25 5.219,2.646 5.99,3.073 0.771,0.427 10 false L25 5.219,1.958 5.99,2.385 0.771,0.427 10 false L25 5.219,1.208 5.99,1.635 0.771,0.427 10 false L26 5.219,0.677 5.99,1.104 0.771,0.427 10 false L26 5.271,1.021 6.042,1.448 0.771,0.427 10 false 14 5.26,1.75 6.031,2.177 0.771,0.427 10 false 26 5.271,2.417 6.042,2.844 0.771,0.427 10 false 28 5.281,3.115 6.052,3.542 0.771,0.427 10 false 15 1.833,2.625 3.094,3 1.26,0.375 10 false from Ignition Switch 2.271,1.927 3.531,2.302 1.26,0.375 10 false from Battery 3.896,2.156 5.156,2.531 1.26,0.375 10 false DOME NO.1 4.156,2.823 5.417,3.198 1.26,0.375 10 false MET

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY CAN MAIN WIRE)
a.
C363466C01
1.385,0.271 1.99,0.552 0.604,0.281 0.427,1.875 0.563,1.875 0.563,1.875 0.781,1.646 true 0.656,2.052 0.792,2.052 0.792,2.052 0.938,1.656 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.521,0.281 1.833,0.438 0.313,0.156 10 false L26 0.031,1.75 0.469,1.938 0.438,0.188 10 false CANH 0.26,1.958 0.698,2.146 0.438,0.188 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L26-13 (CANH) - L26-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE COMBINATION METER ASSEMBLY CAN MAIN WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE CIRCUIT)
a.
C363546C01
1.385,0.219 1.969,0.49 0.583,0.271 0.375,1.854 0.51,1.854 0.51,1.854 0.729,1.49 true 3.083,1.833 2.917,1.833 2.917,1.833 2.698,1.521 true 2.708,2.01 2.542,2.01 2.542,2.01 2.396,1.5 true 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 1.552,0.24 1.865,0.438 0.313,0.198 10 false L25 3.135,1.719 3.406,1.927 0.271,0.208 10 false B 2.76,1.906 3.031,2.115 0.271,0.208 10 false B 0.146,1.75 0.417,1.958 0.271,0.208 10 false ES
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L25-26 (B) - Body ground Always 11 to 14 V
L25-28 (B) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-15 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR