Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0556385 CAN COMMUNICATION SYSTEM(w/ Pre-collision System) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Pre-collision System)  Millimeter Wave Radar Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Millimeter Wave Radar Sensor Communication Stop Mode Communication stop for "Front Radar" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Power source or inside of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit

·

Millimeter wave radar sensor assembly CAN branch wire or connector

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

C494975E01
1.552,0.969 2.042,1.438 0.49,0.469 10 false 8 1.531,1.49 2.021,1.958 0.49,0.469 10 false 19 0.104,1.885 0.677,2.073 0.573,0.188 10 false I134 0.104,2.094 2.542,2.417 2.438,0.323 10 false No. 7 Global CAN Junction Connector 5.427,0.99 5.917,1.458 0.49,0.469 10 false 3 5.427,1.49 5.917,1.958 0.49,0.469 10 false 2 4.063,2.479 5.104,2.677 1.042,0.198 10 false IG1 NO.1 5.396,2.5 5.885,2.969 0.49,0.469 10 false 8 5.656,2.656 6.146,3.125 0.49,0.469 10 false IGB 5.396,3.708 5.885,4.177 0.49,0.469 10 false 1 5.646,3.813 6.292,4.219 0.646,0.406 10 false SGND 5.094,4.771 5.583,5.063 0.49,0.292 10 false I131 5.104,4.958 6.979,5.354 1.875,0.396 10 false Millimeter Wave Radar Sensor Assembly 1.99,2.635 3.698,2.99 1.708,0.354 10 false from IG1 1 Relay 5.656,1.094 6.208,1.458 0.552,0.365 10 false CA2H 5.646,1.615 6.188,1.958 0.542,0.344 10 false CA2L

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
C494971C01
1.49,0.135 1.979,0.354 0.49,0.219 1.792,1.031 1.125,0.479 1.125,0.479 0.99,0.479 true 1.625,1.042 0.885,0.719 0.885,0.719 0.75,0.719 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.594,0.177 2.146,0.469 0.552,0.292 10 false I131 0.563,0.375 1.177,0.573 0.615,0.198 10 false CA2H 0.344,0.615 0.958,0.813 0.615,0.198 10 false CA2L
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I131-3 (CA2H) - I131-2 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE CIRCUIT)
a.
C494971C02
1.51,0.156 2,0.375 0.49,0.219 1.958,1.229 2.396,1.76 2.396,1.76 2.583,1.76 true 1.479,1.042 1.031,0.583 1.031,0.583 0.896,0.583 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.604,0.177 2.177,0.531 0.573,0.354 10 false I131 2.625,1.656 3.052,1.917 0.427,0.26 10 false IGB 0.458,0.5 0.948,0.75 0.49,0.25 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I131-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I131-1 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR