Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with VSC) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0306319 CAN COMMUNICATION SYSTEM(for RHD with VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with VSC)  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of airbag sensor assembly

·

Airbag sensor assembly ground circuit

·

Airbag sensor assembly CAN branch wire or connector

·

Airbag sensor assembly



WIRING DIAGRAM

C279373E31
5.417,3.938 6.781,4.313 1.365,0.375 10 false I51 5.417,4.104 7.031,4.49 1.615,0.385 10 false Airbag Sensor Assembly 5.583,3.313 6.948,3.688 1.365,0.375 10 false E2 5.583,2.708 6.948,3.083 1.365,0.375 10 false E1 5.583,2.125 6.948,2.5 1.365,0.375 10 false IG2 5.583,0.677 6.948,1.052 1.365,0.375 10 false CANH 5.583,1.271 6.948,1.646 1.365,0.375 10 false CANL 5.313,2 6.677,2.375 1.365,0.375 10 false 21 5.302,2.625 6.667,3 1.365,0.375 10 false 25 5.302,3.208 6.667,3.583 1.365,0.375 10 false 26 5.333,1.146 6.698,1.521 1.365,0.375 10 false 22 5.333,0.583 6.698,0.958 1.365,0.375 10 false 13 1.677,0.583 3.042,0.958 1.365,0.375 10 false 1 1.677,1.125 3.042,1.5 1.365,0.375 10 false 2 0.417,1.625 1.781,2 1.365,0.375 10 false I116 0.417,1.792 2.667,2 2.25,0.208 10 false No. 4 CAN Junction Connector 2.125,2.094 4.813,2.385 2.688,0.292 10 false from Ignition Switch 4.354,2.302 5.354,2.594 1,0.292 10 false IGN

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

DTC check procedure: Turn the ignition switch to ON and wait at least 10 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>DIAGNOSIS SYSTEM

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Some parts must be set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
C210016C23
0.302,1 0.75,1.302 0.448,0.302 1.99,1.083 2.438,0.667 2.438,0.667 2.573,0.667 true 2.094,1.302 2.396,1.635 2.396,1.635 2.542,1.635 true 0.052,0.063 0.24,0.24 0.188,0.177 10 false *a 2.625,0.552 3.063,0.729 0.438,0.177 10 false CANH 0.417,1.052 0.885,1.344 0.469,0.292 10 false I51 2.604,1.521 3.042,1.698 0.438,0.177 10 false CANL
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the cable from the negative (-) battery terminal and wait at least 90 seconds.


b.

Disconnect the airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I51-13 (CANH) - I51-22 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
C210016C24
0.323,1.021 0.792,1.323 0.469,0.302 2.188,1.271 2.49,1.104 2.49,1.104 2.625,1.104 true 1.771,1.292 2.083,1.844 2.083,1.844 2.229,1.844 true 1.646,1.313 1.302,1.719 1.302,1.719 1.125,1.719 true 0.052,0.052 0.24,0.229 0.188,0.177 10 false *a 2.677,0.99 3.115,1.167 0.438,0.177 10 false IG2 0.427,1.052 0.927,1.5 0.5,0.448 10 false I51 2.292,1.729 2.729,1.906 0.438,0.177 10 false E1 0.927,1.594 1.365,1.771 0.438,0.177 10 false E2
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I51-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I51-25 (E1) - Body ground Always Below 1 Ω
I51-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE HARNESS AND CONNECTOR