Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3. The DTCs are communicated through SRS warning light blinking patterns.

HINT:

When one or more of the warning lights blink continuously, the cause may be a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in an ECU.


WIRING DIAGRAM

C240459E20
5.51,2.75 6.948,3.125 1.438,0.375 10 false Airbag Sensor Assembly 5.802,1.167 6.177,1.448 0.375,0.281 10 false TC 0.615,2.281 1.031,2.594 0.417,0.313 10 false I17 0.604,2.458 1.094,2.792 0.49,0.333 10 false DLC3 1.583,1.156 1.958,1.458 0.375,0.302 10 false TC 1.552,1.906 1.917,2.24 0.365,0.333 10 false CG 5.521,1.052 5.896,1.333 0.375,0.281 10 false 12 1.844,1.052 2.188,1.333 0.344,0.281 10 false 13 1.885,1.823 2.167,2.094 0.281,0.271 10 false 4 5.5,2.594 5.885,2.875 0.385,0.281 10 false I51

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag sensor with ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DLC3 - AIRBAG SENSOR ASSEMBLY AND BODY GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the I51 connector from the airbag sensor assembly.


d.
C237254C12
1.51,0.125 1.927,0.375 0.417,0.25 1.49,1.604 1.906,1.854 0.417,0.25 0.677,1.135 1.604,0.854 true 2.646,1.375 1.844,1.188 true 2.552,2.76 2.083,2.521 true 0.156,0.104 0.448,0.417 0.292,0.313 10 false *a 0.156,1.625 0.448,1.938 0.292,0.313 10 false *b 1.583,0.167 1.958,0.469 0.375,0.302 10 false I17 0.427,1.073 0.802,1.375 0.375,0.302 10 false CG 2.677,1.333 3.052,1.635 0.375,0.302 10 false TC 2.625,2.75 3,3.052 0.375,0.302 10 false TC 1.573,1.646 1.948,1.948 0.375,0.302 10 false I51
*a Front view of DLC3
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-13 (TC) - I51-12 (TC) Always Below 1 Ω
I17-4 (CG) - Body ground Always Below 1 Ω
I51-12 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR