| Illuminate |
X2000 |
Yaw Rate Sensor Malfunction |
History of yaw rate sensor malfunction signals output by the skid control ECU (brake actuator assembly) |
Refer to How to Proceed with Troubleshooting in Electronically Controlled Brake System. ( ) |
| - |
X2004 |
Speed Sensor Malfunction |
History of vehicle speed sensor malfunction signals output by the skid control ECU (brake actuator assembly) |
Refer to How to Proceed with Troubleshooting in Electronically Controlled Brake System. ( ) |
| Illuminate |
X2014 |
Front Recognition Camera Optical Axis Not Adjusted |
History of beam axis non-adjustment status by the forward recognition camera |
-
HINT:
-
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
-
One Time Recognition:( )
-
Sequential Recognition:( )
-
Driving Adjustment:
-
( )
|
| Illuminate |
X2015 |
Front Recognition Camera Dirt |
History of forward recognition camera being unable to recognize the front and being temporarily unavailable |
-
Front wiper blade other than genuine part may be attached
-
Front wiper rubber may be deteriorated
-
There may be stickers, accessories, baggage, etc. in visual field range of forward recognition camera
-
There may be snow, ice, fog, dirt, frost, dust or oil film sticking on windshield glass in front of camera
-
There may be damage or cracks on windshield glass in front of camera
-
Windshield glass other than genuine part may be installed
-
Confirm the vehicle was not driven in poor weather (the warning display will disappear when the conditions [darkness, backlight, snow, fog, etc.] around the forward recognition camera improve and the forward recognition camera can be used again)
Cause:
When foreign matter or dirt is attached to area around forward recognition camera
|
| Illuminate |
X2016 |
Front Recognition Camera Outside Guaranteed Operating Temperature |
History of forward recognition camera being temporarily unavailable due to high temperature or low temperature |
Using the GTS, check the following items for the front recognition camera in the Data List. ( )
·
Front Recognition Camera Low Temperature
·
Front Recognition Camera High Temperature 1
Cause:
The forward recognition camera is in one of the following conditions
-
When the ambient temperature is approximately -30°C (-22°F) or less, such as when the vehicle is left alone in an extremely cold environment
-
When the ambient temperature is approximately 80°C (176°F) or higher, such as when the vehicle is left alone in an extremely hot environment
|
| Illuminate |
X2017 |
Front Recognition Camera Outside Guaranteed Operating Voltage |
History of forward recognition camera being temporarily unavailable due to low voltage or high voltage |
·
Check the power supply voltage (IGB) of the forward recognition camera. For terminals to check and standard values, click here.
( )
·
If the power supply voltage was within the standard value, the forward recognition camera may be malfunctioning.
Cause:
The forward recognition camera is in one of the following conditions
-
When the input voltage is approximately 9 V or less, immediately after starting the engine
-
When the input voltage is approximately 16 V or higher, immediately after starting the engine
|
| - |
X201C |
Front Recognition Camera Haze |
History of forward recognition camera being unable to recognize the front and being temporarily unavailable |
-
Front wiper blade other than genuine part may be attached
-
Front wiper rubber may be deteriorated
-
There may be stickers, accessories, baggage, etc. in visual field range of forward recognition camera
-
There may be snow, ice, fog, dirt, frost, dust or oil film sticking on windshield glass in front of camera
-
There may be damage or cracks on windshield glass in front of camera
-
Windshield glass other than genuine part may be installed
-
Confirm the vehicle was not driven in poor weather (the warning display will disappear when the conditions [darkness, backlight, snow, fog, etc.] around the forward recognition camera improve and the forward recognition camera can be used again)
Cause:
When foreign matter or dirt is attached to area around forward recognition camera
|
| - |
X204A |
Acceleration Sensor Malfunction |
History of G sensor malfunction signals output by the skid control ECU (brake actuator assembly) |
Refer to How to Proceed with Troubleshooting in Electronically Controlled Brake System. ( ) |
| - |
X204C |
Zero Point Calibration of Yaw Rate Sensor Undone |
History of yaw rate sensor zero point uncorrected signal received from skid control ECU (brake actuator assembly) |
Refer to How to Proceed with Troubleshooting in Electronically Controlled Brake System. ( ) |