Home › Vehicle Interior › PRE-COLLISION › FRONT RADAR SENSOR SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _128087 PRE-COLLISION _0564255 FRONT RADAR SENSOR SYSTEM C

PRE-COLLISION  FRONT RADAR SENSOR SYSTEM  U010487  Lost Communication with Cruise Control Module Missing Message  


DESCRIPTION

The millimeter wave radar sensor assembly communicates with the forward recognition camera via CAN communication.

If a communication error is detected between the forward recognition camera and millimeter wave radar sensor assembly, the millimeter wave radar sensor assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
U010487 Lost Communication with Cruise Control Module Missing Message
Detection condition:

Ignition switch ON


Malfunction status:

Communication malfunction with the forward recognition camera is detected


Malfunction duration:

10 seconds or more


·

Pre-collision system

·

Forward recognition camera

·

Millimeter wave radar sensor assembly



Pattern DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Millimeter Wave Radar Sensor Assembly Forward Recognition Camera
Front Radar Sensor Pre-Collision System
U010487 U023587

○: DTC is output

-: DTC is not output

Pattern 1 ○ ○ Harness or connector (Open or short)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)
Pattern 2 ○ - Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)

HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


WIRING DIAGRAM

C494250E01
0.75,1.906 3.042,2.385 2.292,0.479 10 false Forward Recognition Camera 4.823,1.896 6.219,2.656 1.396,0.76 10 false Millimeter Wave Radar Sensor Assembly 0.75,1.719 1.719,2.229 0.969,0.51 10 false S34*1, Y8*2 4.823,1.719 5.24,1.948 0.417,0.229 10 false I131 1.604,0.792 2.219,0.99 0.615,0.198 10 false CANH 1.615,1.469 2.229,1.667 0.615,0.198 10 false CANL 5.115,0.771 5.729,0.969 0.615,0.198 10 false CA1P 5.125,1.479 5.74,1.677 0.615,0.198 10 false CA1N 2.083,0.781 2.24,0.979 0.156,0.198 10 false 6 2.073,1.25 2.271,1.448 0.198,0.198 10 false 12 4.948,0.771 5.104,0.969 0.156,0.198 10 false 5 4.948,1.24 5.104,1.438 0.156,0.198 10 false 6 0.219,2.438 2.448,2.771 2.229,0.333 10 false *1: for Pickup 1.25,2.448 3.479,2.781 2.229,0.333 10 false *2: except Pickup

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history (RoB). Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereVehicle Interior>PRE-COLLISION>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereVehicle Interior>PRE-COLLISION>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereVehicle Interior>PRE-COLLISION>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history (RoB) for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>DRIVING ADJUSTMENT


·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

·

When disconnecting and reconnecting the battery

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK FOR DTCs
a.

Read each DTC and check the diagnosis pattern using the table below.

Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Pattern DTC Output Part Name
(Display on GTS)
Front Radar Sensor Pre-Collision System
Pattern 1 U010487 U023587
Pattern 2 U010487 -


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

B

2.CHECK FORWARD RECOGNITION CAMERA
2.CHECK FORWARD RECOGNITION CAMERA
a.

Disconnect the I131 millimeter wave radar sensor assembly connector.


b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
I131-5 (CA1P) - I131-6 (CA1N) Ignition switch ON 1 V/DIV., 100 μs./DIV. Pulse generation


Result:
Proceed to
OK
NG




OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPLACE FORWARD RECOGNITION CAMERA