Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for Single Cab) › from 2022.09
RM25T0E _58 Vehicle Interior _029934 INTERIOR PANELS / TRIM _0142494 ROOF HEADLINING(for Single Cab) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for Single Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 63310 1.INSTALL ROOF HEADLINING ASSEMBLY

a.

w/o Knee Airbag:

i.
B234365

Place the roof headlining assembly into the vehicle through the front door.

NOTICE:
·

Check that the corners of the roof headlining assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.




ii.
B234363

Install the roof headlining assembly with the 8 clips.



b.

w/ Driver Side Knee Airbag:

i.
B452005

Place the roof headlining assembly into the vehicle through the front door.

NOTICE:
·

Check that the corners of the roof headlining assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.




ii.
B452004

Install the roof headlining assembly with the 4 clips.



c.

w/ Pre-collision System:

i.
B666269

Connect the 2 connectors.



Hide 74348 2.INSTALL VISOR HOLDER

HINT:

Use the same procedure for both visor holders.


a.

Attach the clip to install the visor holder.


b.

Install the screw.


Hide 74320 3.INSTALL VISOR ASSEMBLY LH

a.

Install the visor assembly LH with the 2 screws.


Hide 74310 4.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 81290 5.INSTALL NO. 3 ROOM LIGHT ASSEMBLY

Hide 63388G 6.INSTALL NO. 2 ROOF HEADLINING HOLDER COVER (w/ Pre-collision System)

a.
B666271

Attach the guide and claw to install the No. 2 roof headlining holder cover.


Hide 86466D 7.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Hide 87810 8.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

Hide 87834 9.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER

Hide 87827 10.INSTALL INNER REAR VIEW MIRROR ABSORBER

Hide 74610A 11.INSTALL ASSIST GRIP SUB-ASSEMBLY

a.

Install the assist grip sub-assembly with the 2 screws.


Hide 74617C 12.INSTALL ASSIST GRIP PLUG

HINT:

Use the same procedure for all assist grip plugs.


a.

Attach the 2 claws to install the assist grip plug.


Hide 73024 13.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH (w/ Driver Side Knee Airbag)

a.

Attach the 6 guides to install the front shoulder belt anchor plate sub-assembly LH.


Hide 73023 14.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH (w/ Driver Side Knee Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 62412 15.INSTALL CENTER PILLAR GARNISH LH

a.
B452046C01
0.938,1.385 1.406,1.385 1.406,1.385 1.292,1.104 false 3.063,1.729 2.958,1.729 2.958,1.729 2.896,1.49 true 0.74,1.292 1.052,1.49 0.313,0.198 10 false *a 3.073,1.646 3.385,1.844 0.313,0.198 10 false *a
*a String


Apply a string along the back window glass weatherstrip groove, as shown in the illustration.


b.

w/o Knee Airbag:

i.
B234358

Attach the 5 clips to temporarily install the center pillar garnish LH.


ii.

Install the 3 clips.


iii.

Connect the front seat belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


iv.

Connect the front seat belt shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


v.

Attach the 2 claws to close the front seat belt shoulder anchor cover.



c.

w/ Driver Side Knee Airbag:

i.
B461228

Install the 2 clips to the center pillar garnish LH.


ii.
B452001

Attach the 8 clips to install the center pillar garnish LH.


iii.

Install the 2 clips.


iv.

Connect the front seat belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



d.
B452044C01
0.854,1.781 0.979,1.781 0.979,1.781 1.417,1.51 false 0.958,0.354 1.073,0.354 1.073,0.354 1.146,0.531 false 0.667,1.688 0.979,1.885 0.313,0.198 10 false *a 0.771,0.25 1.083,0.448 0.313,0.198 10 false *a
*a String


While pressing the center pillar garnish LH by hand, using a string, pull out the lip groove of the back door weatherstrip towards the vehicle interior.


Hide 62411 16.INSTALL CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 58707A 17.INSTALL JACK HOLDER SUB-ASSEMBLY (w/o Knee Airbag)

a.

Install the jack holder sub-assembly with the 2 bolts.


Hide 73174 18.INSTALL FRONT SEAT BELT HOLE COVER LH (w/o Knee Airbag)

a.

Attach the 2 guides and 2 claws to install the front seat belt hole cover LH.


Hide 73173 19.INSTALL FRONT SEAT BELT HOLE COVER RH (w/o Knee Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 62212 20.INSTALL FRONT PILLAR GARNISH LH

a.

w/o Knee Airbag:

Attach the clip and claw to install the front pillar garnish LH.


b.

w/ Driver Side Knee Airbag:

i.
B452043

Install the clip to the vehicle side.


ii.
B452045

Temporarily install the front pillar garnish LH as indicated by the arrow shown in the illustration.


iii.

Attach the clip to install the front pillar garnish LH.



Hide 62211 21.INSTALL FRONT PILLAR GARNISH RH

a.

w/o Knee Airbag:

HINT:

Use the same procedure described for the LH side.



b.

w/ Driver Side Knee Airbag:

HINT:

Use the same procedure described for the LH side.



c.

w/o Assist Grip:

i.

Attach the clip and claw to install the front pillar garnish LH.


ii.

Install the 2 clips.



Hide 74603 22.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for both front assist grip sub-assemblies.


a.

Install the front assist grip sub-assembly with the 2 screws.


Hide 74617A 23.INSTALL ASSIST GRIP PLUG

HINT:

Use the same procedure for all assist grip plugs.


a.

Attach the 2 claws to install the assist grip plug.


Hide 55356B 24.INSTALL INSTRUMENT PANEL PLATE LH

Hide 55355B 25.INSTALL INSTRUMENT PANEL PLATE RH

Hide 62316C 26.INSTALL FRONT DOOR REAR OPENING TRIM WEATHERSTRIP LH

a.

Install the front door rear opening trim weatherstrip LH.


Hide 62315E 27.INSTALL FRONT DOOR REAR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 62112A 28.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

a.

Attach the clip to install the cowl side trim sub-assembly LH.


b.

Install the cap nut.


Hide 62111A 29.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 67914 30.INSTALL FRONT DOOR SCUFF PLATE LH

a.

Install the front door scuff plate LH with the 4 screws.


Hide 67913 31.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.