Home › General › MAINTENANCE › Q710 HYBRID TRANSAXLE FLUID
RM37H0E _V1 General _095083 MAINTENANCE _0447215 Q710 HYBRID TRANSAXLE FLUID A

MAINTENANCE  Q710 HYBRID TRANSAXLE FLUID  REPLACEMENT  


PROCEDURE

Hide 52383E 1.REMOVE NO. 1 DIFFERENTIAL SUPPORT PROTECTOR

a.
C448573C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, nut and No. 1 differential support protector.


Hide 52384C 2.REMOVE NO. 2 DIFFERENTIAL SUPPORT PROTECTOR

a.
C448572C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, nut and No. 2 differential support protector.


Hide 53661B 3.REMOVE REAR SUSPENSION BRACE COVER

a.
C448574C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 4 bolts and 2 nuts from the rear suspension brace cover.


Hide 4.REPLACE HYBRID TRANSAXLE FLUID

a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.
C447914

Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the FCV with motor transaxle assembly.


c.
C447915

Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the FCV with motor transaxle assembly and drain the hybrid transaxle fluid.


d.

Using a 10 mm hexagon socket wrench, install a new gasket and the drain plug to the FCV with motor transaxle assembly.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


e.
C447916C02
2.333,1.115 2.5,0.833 2.5,0.833 2.667,0.833 false 2.708,0.75 2.875,0.917 0.167,0.167 10 false *a 3.104,1.719 3.271,1.885 0.167,0.167 10 false *b
*a Filler Nozzle
*b 0 to 8 mm (0 to 0.315 in.)


Add hybrid transaxle fluid until the hybrid transaxle fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening. [*]

NOTICE:
·

When adding hybrid transaxle fluid, make sure that the vehicle is level.

·

Use Toyota Genuine ATF WS.

Using transmission fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transmission of your vehicle.

·

Be sure to fully insert the filler nozzle into the filler plug opening.

·

Be sure to add hybrid transaxle fluid slowly. If hybrid transaxle fluid is added quickly, the hybrid transaxle fluid may hit internal parts and bounce back, resulting in hybrid transaxle fluid coming out of the filler plug opening.

·

Be sure to directly check that the hybrid transaxle fluid level is within the specified range.

·

Driving the vehicle with an insufficient or excessive amount of hybrid transaxle fluid may damage the FCV with motor transaxle assembly.



Hybrid Transaxle Fluid Standard Capacity (for Reference):

5.6 liters (5.9 US qts, 4.9 Imp. qts)



f.

After adding fluid, leave it for 30 seconds so that the fluid surface can become still again, and then check that the fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening. (If the hybrid transaxle fluid level is low, repeat this procedure from step [*].)

NOTICE:

After adding hybrid transaxle fluid, make sure to check the hybrid transaxle fluid level.



g.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the FCV with motor transaxle assembly.

HINT:

Reuse the old gasket as the filler plug will be removed again.



h.

Lower the vehicle.


Hide 6.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

a.

Make sure that there are no hybrid transaxle fluid leaks from the work site joints and clamps.


Hide 53661B 7.INSTALL REAR SUSPENSION BRACE COVER

a.

Install the rear suspension brace cover with the 4 bolts and 2 nuts.


Hide 52384C 8.INSTALL NO. 2 DIFFERENTIAL SUPPORT PROTECTOR

a.

Install the No. 2 differential support protector with the 2 bolts and nut.


Hide 52383E 9.INSTALL NO. 1 DIFFERENTIAL SUPPORT PROTECTOR

a.

Install the No. 1 differential support protector with the 2 bolts and nut.