84306
1.INSPECT SPIRAL CABLE SUB-ASSEMBLY
Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.
Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.
Visually check the spiral cable sub-assembly for defects.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
- | - |
|
Interlock | - | - |
When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Set the spiral cable sub-assembly to the center position.
Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
Inspect the SRS airbag circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
|
Click Location & Routing(D31,z8)Location & Routingewd_type=routing;type=c,c;code=D31,z8 Click Connector(D31)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=D31;pinno=1,2 Click Connector(z8)Instrument Panel>other>Driver Side Squib Circuit (Horn Button Assembly) , Spiral Cable Sub-Assemblyewd_type=component;type=c;code=z8;pinno=2,1 |
||
| D31-1 (D+) - z8-2 | Always | Below 1.3 Ω |
| D31-2 (D-) - z8-1 | Always | Below 1.3 Ω |
Inspect the horn circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
|
Click Location & Routing(D32)Location & Routingewd_type=routing;type=c;code=D32 Click Connector(D32)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=D32;pinno=7 |
||
| D32-7 (HO) - A | Always | 3 Ω or less |
Inspect the steering pad switch circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
|
Click Location & Routing(D32,z5)Location & Routingewd_type=routing;type=c,c;code=D32,z5 Click Connector(D32)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=D32;pinno=4,5,9,10,11,12,14 Click Connector(z5)Instrument Panel>other>Spiral Cable Sub-Assembly , Steering Pad Switch Assemblyewd_type=component;type=c;code=z5;pinno=10,9,6,5,4,3,1 |
||
| D32-4 (EAU) - z5-10 | Always | 3 Ω or less |
| D32-5 (AU2) - z5-9 | Always | 3 Ω or less |
| D32-9 (ILL-) - z5-6 | Always | 3 Ω or less |
| D32-10 (+DP2) - z5-5 | Always | 3 Ω or less |
| D32-11 (+DP) - z5-4 | Always | 3 Ω or less |
| D32-12 (AU1) - z5-3 | Always | 3 Ω or less |
| D32-14 (IL+2) - z5-1 | Always | 3 Ω or less |
Inspect the cruise control circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
|
Click Location & Routing(D32,z5)Location & Routingewd_type=routing;type=c,c;code=D32,z5 Click Connector(D32)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=D32;pinno=2,6,13 Click Connector(z5)Instrument Panel>other>Spiral Cable Sub-Assembly , Steering Pad Switch Assemblyewd_type=component;type=c;code=z5;pinno=12,8,2 |
||
| D32-2 (ECC) - z5-12 | Always | 3 Ω or less |
| D32-6 (DIST) - z5-8 | Always | 3 Ω or less |
| D32-13 (CCS) - z5-2 | Always | 3 Ω or less |
Inspect the steering heater circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
|
Click Location & Routing(D33,z9)Location & Routingewd_type=routing;type=c,c;code=D33,z9 Click Connector(D33)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=D33;pinno=2,3,4 Click Connector(z9)Instrument Panel>other>Steering ECU (Steering Wheel Assembly) , Spiral Cable Sub-Assemblyewd_type=component;type=c;code=z9;pinno=1,3,4 |
||
| D33-2 (EHT) - z9-1 | Always | Below 1.3 Ω |
| D33-3 (LIN) - z9-3 | Always | Below 1.3 Ω |
| D33-4 (BHT) - z9-4 | Always | Below 1.3 Ω |