Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0448067 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B605573N03
4.365,3.167 6.958,4.438 2.594,1.271 6.521,0.25 6.844,0.25 false 1.5,1.396 1.5,1.938 false 5.073,4.094 5.073,3.844 false 6.667,3.646 6.417,3.646 false 1.448,4.198 1.448,4.438 1.448,4.438 1.635,4.438 false 6.469,0.677 6.792,0.677 false 4.24,1.698 4.563,1.698 false 4.083,3.75 4.365,3.75 false 5.771,0.104 7.156,0.5 1.385,0.396 18 false 1, 7, 9 2.813,3.177 3.125,3.375 0.313,0.198 10 false x 3 4.083,1.552 4.365,1.906 0.281,0.354 18 false 8 1.719,4.271 2,4.625 0.281,0.354 18 false 6 1.458,1.958 1.74,2.313 0.281,0.354 18 false 5 3.948,3.625 4.313,3.938 0.365,0.313 18 false 4 5.01,4.135 5.375,4.448 0.365,0.313 18 false 2 6.75,3.583 7.063,3.781 0.313,0.198 10 false *1 5.792,0.521 6.688,0.875 0.896,0.354 18 false 10-12

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY 84306 (Click here) - -
2 STEERING SENSOR - (Click here) - -
3 FRONT WHEELS FACING STRAIGHT AHEAD - - - -
4 SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY 84306 (Click here) - -
5 UPPER STEERING COLUMN COVER 45286B - - -
6 LOWER STEERING COLUMN COVER 45287 - - -
7 ADJUST SPIRAL CABLE SUB-ASSEMBLY 84306 (Click here) - -
8 STEERING WHEEL ASSEMBLY 45100 - - -
9 CHECK SRS WARNING LIGHT - (Click here) - -
10 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)
11 CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM - - - (Click here)
12 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)

*1 SPIRAL CABLE SUB-ASSEMBLY - -

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

a.
B574512C03
0.333,0.583 6.833,2.5 6.5,1.917 0.927,1.323 1.5,1.323 true 4.958,1.24 4.958,0.719 4.958,0.719 4.531,0.719 true 4.323,1.302 4.896,1.302 true 0.583,1.417 1.531,1.417 true 3.583,2.5 3.583,0.583 false 4.896,1.75 4.813,2.083 4.813,2.083 4.813,1.833 true 1.5,1.771 1.417,2.104 1.417,2.104 1.417,1.854 true 0.375,0.625 0.708,0.948 0.333,0.323 12 false *A 3.615,0.615 4.021,0.969 0.406,0.354 12 false *B 0.76,1.229 1.073,1.385 0.313,0.156 10 false *a 4.76,2.094 4.938,2.271 0.177,0.177 10 true *b 0.396,1.323 0.708,1.479 0.313,0.156 10 false *c 4.344,0.635 4.656,0.792 0.313,0.156 10 false *d 4.146,1.208 4.458,1.365 0.313,0.156 10 false *a 1.344,2.104 1.521,2.281 0.177,0.177 10 true *b 0.594,0.208 0.927,0.531 0.333,0.323 18 false i
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn


i.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.




b.
B573461C04
1.167,2 5.917,3.667 4.75,1.667 6.177,1.083 6.75,1.083 true 3.979,2.833 4.479,2.833 true 1.49,2.917 1.99,2.917 true 1.583,2.583 1.75,2.583 1.75,2.583 2.052,2.865 true 4.083,2.5 4.25,2.5 4.25,2.5 4.521,2.792 true 0.75,1.083 1.396,1.083 true 3.5,3.667 3.5,2 false 2.021,3.198 1.938,3.448 1.938,3.448 1.938,3.281 false 4.49,3.177 4.406,3.427 4.406,3.427 4.406,3.26 false 0.521,0.104 0.802,0.458 0.281,0.354 18 false i 2.854,0.469 3.135,0.823 0.281,0.354 18 false 2 5.146,0.458 5.427,0.813 0.281,0.354 18 false 3 0.854,1.99 1.135,2.344 0.281,0.354 18 false 4 1.219,2.063 1.594,2.302 0.375,0.24 12 false *A 3.542,2.052 3.917,2.292 0.375,0.24 12 false *B 6.813,1 7.052,1.156 0.24,0.156 10 false *a 3.771,2.76 4.01,2.917 0.24,0.156 10 false *b 1.292,2.844 1.531,3 0.24,0.156 10 false *b 1.354,2.51 1.594,2.667 0.24,0.156 10 false *d 3.875,2.427 4.115,2.583 0.24,0.156 10 false *e 4.354,3.448 4.542,3.604 0.188,0.156 10 true *c 1.875,3.469 2.063,3.625 0.188,0.156 10 true *c 0.542,1 0.781,1.156 0.24,0.156 10 false *a 0.573,0.51 0.854,0.865 0.281,0.354 18 false 1
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Interlock *b Check Window
*c Matchmark *d Colored Roller
*e Top of Flat Cable U-turn - -
V113147

Rotation Direction - -


i.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

When rotating the spiral cable sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



1. While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.


HINT:

The interlock operates at the top and bottom of the connector.


2. If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.

3. While pushing on the interlock, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.


4. Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 2.INSTALL STEERING SENSOR

Z101186

NOTICE:

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.



a.
B573470C01
0.521,0.177 0.938,0.5 0.417,0.323 18 false ii 4.604,0.198 5.021,0.521 0.417,0.323 18 false iii 1.438,0.865 1.615,1.042 0.177,0.177 10 true *a 3.25,0.844 3.427,1.021 0.177,0.177 10 true *a 3.979,0.698 4.219,1.073 0.24,0.375 18 false i
*a Pin - -


i.

Align the pin to install the steering sensor to the spiral cable sub-assembly.


ii.

Attach the claw to install the steering sensor to the spiral cable sub-assembly.

NOTICE:
·

Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.

·

Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.

·

The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.




iii.

Remove the lock pin from the steering sensor.



Hide 3.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

a.
C447753


Hide 84306 4.INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Z101186

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly with the battery connected and the ignition switch on (IG).

·

When rotating the spiral cable with sensor sub-assembly to check the operation of the spiral cable with sensor sub-assembly (checking for abnormal noise, checking the DTC, Data List, etc.) make sure to perform the inspection with the steering wheel assembly installed.




a.
B605562C01
1.042,0.458 1.833,0.458 true 0.458,0.104 0.74,0.458 0.281,0.354 18 false i 4.49,0.156 4.771,0.51 0.281,0.354 18 false ii 0.813,0.375 1.042,0.604 0.229,0.229 10 true *a
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B605574N01
0.542,0.104 0.823,0.458 0.281,0.354 18 false i 4.26,0.125 4.542,0.479 0.281,0.354 18 false ii

i.

Check that the front wheels are facing straight ahead.


ii.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the turn signal switch cancel ratchet may snap.




c.
B593195N02
0.396,0.073 0.677,0.427 0.281,0.354 18 false i 4.073,0.094 4.354,0.448 0.281,0.354 18 false ii

i.

Attach the claw and clip to install the spiral cable with sensor sub-assembly.


ii.

Connect the 5 connectors.

HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR




Hide 45286B 5.REMOVE UPPER STEERING COLUMN COVER

Hide 45287 6.REMOVE LOWER STEERING COLUMN COVER

Hide 84306 7.ADJUST SPIRAL CABLE SUB-ASSEMBLY

Z101186

NOTICE:

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch on (IG).



a.
B605562C01
1.042,0.458 1.833,0.458 true 0.458,0.104 0.74,0.458 0.281,0.354 18 false i 4.49,0.156 4.771,0.51 0.281,0.354 18 false ii 0.813,0.375 1.042,0.604 0.229,0.229 10 true *a
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B574511C06
0.052,0.5 6.917,2.583 6.865,2.083 0.271,1.354 0.74,1.354 0.74,1.354 0.74,1.594 true 0.75,1.802 0.75,2.375 true 3.656,1.292 4.188,1.292 4.188,1.292 4.188,1.521 true 4.146,1.688 4.146,2.292 true 3.417,2.583 3.417,0.5 false 0.115,0.583 0.417,0.833 0.302,0.25 12 false *A 3.448,0.583 3.781,0.896 0.333,0.313 12 false *B 0.104,1.281 0.365,1.49 0.26,0.208 10 false *a 0.677,2.406 0.938,2.615 0.26,0.208 10 false *b 4.063,2.323 4.323,2.615 0.26,0.292 10 false *c 3.479,1.208 3.792,1.365 0.313,0.156 10 false *a 0.417,0.115 0.719,0.365 0.302,0.25 18 false i
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Check Window *b Colored Roller
*c Top of Flat Cable U-turn - -


i.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.




c.
B573462C04
0.667,2.167 6.333,3.75 5.667,1.583 5.25,1.083 5.906,1.083 true 0.917,3.333 1.26,3.333 true 0.917,2.833 1.083,2.833 1.083,2.833 1.333,3.271 true 3.833,2.833 4,2.833 4,2.833 4.083,3.271 true 0.417,1.083 1.083,1.083 true 3.833,3.646 4,3.646 4,3.646 4.083,3.396 true 3.5,3.75 3.5,2.167 false 0.49,0.115 0.771,0.469 0.281,0.354 18 false i 2.802,0.479 3.083,0.833 0.281,0.354 18 false 2 5.052,0.479 5.333,0.833 0.281,0.354 18 false 3 0.219,2 0.5,2.354 0.281,0.354 18 false 4 0.708,2.25 1.083,2.49 0.375,0.24 12 false *A 3.531,2.25 3.906,2.49 0.375,0.24 12 false *B 5,1.01 5.24,1.167 0.24,0.156 10 false *a 3.688,3.573 3.927,3.729 0.24,0.156 10 false *b 0.75,3.26 0.99,3.417 0.24,0.156 10 false *b 3.667,2.76 3.906,2.917 0.24,0.156 10 false *d 0.729,2.771 0.917,2.927 0.188,0.156 10 false *c 0.198,1.01 0.438,1.167 0.24,0.156 10 false *a 0.344,0.479 0.625,0.833 0.281,0.354 18 false 1
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Interlock *b Check Window
*c Colored Roller *d Top of Flat Cable U-turn
V113147

Rotation Direction - -


i.

If the spiral cable with sensor sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable with sensor sub-assembly.

·

When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



1. While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.


2. If the spiral cable with sensor sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.

3. While pushing on the interlock, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.


4. Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.



ii.

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.



Hide 45100 8.INSTALL STEERING WHEEL ASSEMBLY

Hide 10. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 11. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

Z101186

HINT:

Return the customization settings to the settings before changing them.




Hide 12. PERFORM DIAGNOSTIC SYSTEM CHECK