| *A | w/ Seat Heater System | *B | w/ Occupant Detection Sensor |
| *1 | REAR SEAT CUSHION PAD SUB-ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |
| *A | w/ Combination Switch | *B | w/o Combination Switch |
| *1 | REAR CENTER SEAT ARMREST COVER | *2 | REAR SEAT ARMREST PLATE |
| *3 | REAR SEAT STOPPER PLATE | - | - |
| *A | w/ Seat Heater System | *B | w/o Seat Heater System |
| *C | w/ Climate Control Seat System | - | - |
| *1 | REAR SEATBACK PAD SUB-ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
71075B
1.REMOVE BENCH TYPE REAR SEAT CUSHION COVER
|
|
| *A | w/ Seat Heater System | *B | w/ Occupant Detection Sensor |
Detach the hook.
Detach the fastening tape.
w/ Seat Heater System:
1. Detach the clamp of seat heater.
w/ Occupant Detection Sensor:
1. Detach the clamp of occupant detection sensor.
w/ Occupant Detection Sensor:
Detach the clamp of rear No. 2 seat wire.
Using a thin-bladed screwdriver, detach the claw to remove the bench type rear seat cushion cover from the rear seat cushion pad sub-assembly as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
87510Q
3.REMOVE SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
Use the same procedure described for the RH Side.
82193B
4.REMOVE REAR NO. 2 SEAT WIRE
71940A
5.REMOVE REAR SEAT HEADREST ASSEMBLY
|
Remove in this Direction | - | - |
71960B
6.REMOVE REAR CENTER SEAT HEADREST ASSEMBLY
|
Remove in this Direction | - | - |
72830
7.REMOVE REAR CENTER SEAT ARMREST ASSEMBLY
| *A | w/ Combination Switch | *B | w/o Combination Switch |
|
Nut |
|
Connector |
71281A
8.REMOVE REAR CENTER SEAT ARMREST HINGE
| *1 | Rear Seat Stopper Plate | - | - |
72868
9.REMOVE CENTER ARMREST HINGE COVER RH
72869
10.REMOVE CENTER ARMREST HINGE COVER LH
Use the same procedure described for the RH Side.
66990
12.REMOVE CUP HOLDER ASSEMBLY
| *A | w/o Combination Switch | *B | w/ Combination Switch |
| *1 | Rear Center Seat Armrest Cover | *2 | Rear Seat Armrest Plate |
|
Remove in this Direction | - | - |
13.REMOVE HEADREST SUPPORT
|
Remove in this Direction | - | - |
71077B
14.REMOVE BENCH TYPE REAR SEATBACK COVER
|
|
| *A | w/ Seat Heater System | - | - |
| *a | Fastening Tape | - | - |
w/ Seat Heater System:
1. Disconnect the 2 connectors and detach the clamp.
Detach the hook.
Detach the fastening tape.
Using a thin-bladed screwdriver, detach the claw to remove the bench type rear seatback cover from the rear seatback pad sub-assembly as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
87510S
16.REMOVE SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
Use the same procedure described for the RH Side.
82193A
17.REMOVE REAR NO. 1 SEAT WIRE (w/ Seat Heater System)
The illustrations are representative examples, and details may differ.
87501D
18.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
85867B
19.REMOVE REAR SEATBACK CLIMATE CONTROL BLOWER RH (w/ Climate Control Seat System)
85867C
20.REMOVE REAR SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)
Use the same procedure described for the RH Side.
82668F
21.REMOVE CONNECTOR HOLDER (w/o Seat Heater System)