Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SENSOR
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0448135 BLIND SPOT MONITOR SENSOR N

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SENSOR  ADJUSTMENT  


PROCEDURE

Hide 1.PERFORM BLIND SPOT MONITOR BEAM AXIS CONFIRMATION

HINT:

The blind spot monitor beam axis confirmation is performed to confirm whether the sensor's beam axis is correct, and perform adjustment of the beam axis by using reflector.


a.

When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

E305141C04
0.927,0.354 1.24,0.51 0.313,0.156 12 false *A 3.854,0.375 4.167,0.531 0.313,0.156 12 false *B 2.688,0.51 3,0.667 0.313,0.156 10 false *a 3.042,1.885 3.354,2.042 0.313,0.156 10 false *b 1.365,4.406 1.677,4.563 0.313,0.156 10 false *c 4.292,0.5 4.604,0.656 0.313,0.156 10 false *a 4.021,1.885 4.333,2.042 0.313,0.156 10 false *b 0.802,1.74 1.115,1.896 0.313,0.156 10 false a 6.24,1.719 6.573,1.885 0.333,0.167 10 false a 6.26,2.521 6.573,2.688 0.313,0.167 10 false b 0.719,2.521 1.031,2.688 0.313,0.167 10 false b 1.865,3.604 2.177,3.76 0.313,0.156 10 false c 5.052,3.563 5.365,3.719 0.313,0.156 10 false c
*A Left Side of Vehicle *B Right Side of Vehicle
*a Vehicle Center Line *b Rear Bumper
*c Inspection Area - -


Standard:
Location Measurement
a 1 m (3.28 ft.)
b 5 m (16.40 ft.)
c 6 m (19.68 ft.)


NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place any objects other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 6 m [19.68 ft.] x L 6 m [19.68 ft.] x H 3 m [9.84 ft.] ) shown in the illustration.




b.

Place the reflector.

i.

Hang a weight with a pointed tip from the center of the rear emblem, and mark the rear center point of the vehicle (point A) on the ground.

B601035C02
3.167,2.5 3.365,2.313 3.365,2.313 3.625,2.313 false 3.156,2.625 3.615,2.625 false 5.354,0.865 5.667,0.563 5.667,0.563 5.906,0.563 true 5.365,2.177 5.74,2.302 false 5.813,2.292 6.125,2.448 0.313,0.156 10 true *a 3.708,2.24 4.021,2.396 0.313,0.156 10 false *b 5.979,0.51 6.292,0.667 0.313,0.156 10 true *c 5.094,1.802 5.344,1.99 0.25,0.188 10 true *d 5.438,1.802 5.635,1.969 0.198,0.167 10 true *d 3.74,2.563 3.896,2.76 0.156,0.198 10 false A
*a String *b Weight
*c Center Point *d Bilateral Symmetry


HINT:

Lightly flick the string with your fingers several times to confirm that the string is aligned with mark A.



ii.

Hang a weight with a pointed tip from the center of the radiator grille (or front panel) emblem, and mark the front center point of the vehicle (point B) on the ground.

B601036C02
1.854,1.052 2.198,0.75 2.198,0.75 2.479,0.75 true 1.854,2.208 2.302,2.396 false 3.917,2.344 3.51,2.177 false 3.948,2.438 3.573,2.563 false 2.365,2.375 2.677,2.531 0.313,0.156 10 true *a 3.323,2.094 3.635,2.25 0.313,0.156 10 false *b 2.583,0.677 2.813,0.865 0.229,0.188 10 true *c 1.594,1.938 1.802,2.135 0.208,0.198 10 true *d 1.917,1.938 2.135,2.167 0.219,0.229 10 true *d 3.448,2.5 3.604,2.698 0.156,0.198 10 false B
*a String *b Weight
*c Center Point *d Bilateral Symmetry


HINT:

Lightly flick the string with your fingers several times to confirm that the string is aligned with mark B.



iii.
E238824C05
0.635,1.26 1.094,0.448 false 1.094,0.448 1.292,0.448 false 1.281,1.302 1.438,1.458 0.156,0.156 10 false A 3.052,1.323 3.208,1.479 0.156,0.156 10 false B 1.344,0.385 1.656,0.583 0.313,0.198 10 false *a
*a Vehicle Center Line


Draw a vehicle center line so that it passes through mark A and B (front and rear center points).


iv.

Enlarge and print out the poster shown in the illustration.

B554823C02
4.594,4.438 4.594,4.021 4.594,4.021 5.01,4.021 false 4.417,2.271 4.083,2.271 4.083,2.271 4.083,1.854 false 3.927,6.833 3.927,6.417 3.927,6.417 4.344,6.417 false 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 1.927,3.313 2.24,3.469 0.313,0.156 10 false *b 4.458,2.188 4.771,2.344 0.313,0.156 10 false *c 5.052,3.938 5.365,4.094 0.313,0.156 10 false *d 4.396,6.344 4.708,6.5 0.313,0.156 10 false *c 2.656,4.073 2.813,4.271 0.156,0.198 10 false a 2.656,4.667 2.813,4.865 0.156,0.198 10 false a 1.969,4.573 2.125,4.771 0.156,0.198 10 false A
*a Poster *b Edge of Rear Bumper
*c Line C *d Vehicle Center Line


Standard:
Part Angle
a 51.2°



v.
E334361C03
0.844,1.531 1.115,1.531 1.115,1.531 1.813,1.938 true 1.833,2.906 2.385,2.896 false 2.833,2.49 2.438,2.49 2.438,2.49 1.969,2.156 true 0.729,1.469 0.885,1.667 0.156,0.198 10 false A 2.427,2.854 2.74,3.052 0.313,0.198 10 false *b 2.875,2.438 3.188,2.635 0.313,0.198 10 false *a
*a Poster
*b Vehicle Center Line


Attach the printed poster to the floor with the vehicle center line aligned with point A as shown in the illustration.


vi.
E334362C04
2.073,3.771 1.865,3.771 1.865,3.771 1.813,3.375 false 2.781,3.292 2.479,3.292 2.479,3.292 2.344,3.542 false 2.813,2.438 2.344,2.448 2.344,2.448 1.729,3.167 true 0.583,3.74 0.74,3.938 0.156,0.198 10 false D 2.771,3.719 2.927,3.917 0.156,0.198 10 false D 0.271,0.302 0.583,0.479 0.313,0.177 10 false *a 1.625,4.396 1.938,4.573 0.313,0.177 10 false *b 2.146,3.719 2.458,3.896 0.313,0.177 10 false *d 2.833,3.219 3.146,3.396 0.313,0.177 10 false *c 2.885,2.365 3.042,2.563 0.156,0.198 10 false A
*a Vehicle Front
*b Vehicle Center Line
*c String
*d Poster


Align a piece of string with line C and mark point D at a distance of 3358 mm (11.01 ft.) from point A.


vii.

Set the reflector at the point D shown in the illustration below.

SST
09870-60000  (09870-60010)
09870-60040  

E334360C04
1.229,2.927 0.969,2.5 0.969,2.5 0.646,2.5 true 5.948,2.896 6.281,2.531 6.281,2.531 6.604,2.531 true 2.406,2.24 2.75,2.479 false 4.365,2.438 4.74,2.26 false 1.521,0.615 1.854,0.854 0.333,0.24 12 false *A 3.958,0.604 4.271,0.917 0.313,0.313 12 false *B 2.323,3.281 2.635,3.438 0.313,0.156 10 false *a 0.458,2.438 0.771,2.594 0.313,0.156 10 false *b 4.656,3.24 4.969,3.396 0.313,0.156 10 false *a 1.625,2.427 2.063,2.615 0.438,0.188 10 false a 5.385,2.385 5.823,2.573 0.438,0.188 10 false a 1.01,3 1.354,3.188 0.344,0.188 10 false D 6.083,3.021 6.427,3.208 0.344,0.188 10 false D 6.656,2.458 6.969,2.615 0.313,0.156 10 false *b 2.792,2.49 2.948,2.688 0.156,0.198 10 false A 4.25,2.448 4.406,2.646 0.156,0.198 10 false A
*A Left Side of Vehicle *B Right Side of Vehicle
*a Vehicle Center Line *b Reflector


Standard:
Part Length
a 3358 mm (11.01 ft.)


NOTICE:
·
E238830C07
1.469,0.667 1.979,0.667 1.979,0.667 1.625,1.177 false 2.031,0.594 2.344,0.792 0.313,0.198 10 false *a 0.604,1.563 0.917,1.76 0.313,0.198 10 false *b
*a SST (Reflector)
*b 657 mm (2.15 ft.)


Set the reflector so that its center is 657 mm (2.15 ft.) above the ground.

·
E338853C04
2.125,0.719 2.396,1.438 true 2.417,1.5 2.74,1.729 0.323,0.229 10 false *a
*a Center of Triangular Pyramid


The center of the triangular pyramid is the reference point for the setting position and angle.





c.

Perform the blind spot monitor beam axis display.

i.

Turn the blind spot monitor system on.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Display
50005 313 4238
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Display
50005 314 4239
HINT:

The master beam is on the RH side and the slave beam is on the LH side.

Part Name Tester Item Expression in Others
Blind Spot Monitor Sensor RH Blind Spot Monitor Master Blind Spot Monitor Sensor RH (B)
Blind Spot Monitor Sensor LH Blind Spot Monitor Slave Blind Spot Monitor Sensor LH (A)



ii.

Check the results displayed for the BSM beam axis display.

Allowable Range:
Item Blind Spot Monitor Sensor RH (Master) Blind Spot Monitor Sensor LH (Slave)
Angle -3.6 to +3.6° -3.6 to + 3.6°


HINT:

If the displayed results are outside the permissible range, the following are possible causes. Therefore, implement countermeasures, check the blind spot monitor beam axis and perform the procedure again.

Possible Causes Countermeasure
Incorrect SST (reflector) position Check the position of SST (reflector) and checking space and perform the procedure again
A metallic object is located in the vicinity of the checking space Check the position of SST (reflector) and checking space and perform the procedure again
The blind spot monitor sensor installation is abnormal Check the installation condition of the blind spot monitor sensor




d.

Perform the blind spot monitor beam axis adjustment.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Adjustment
50005 313 4231
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Adjustment
50005 314 4232
HINT:

When values on the axis display are in the allowable range, performing this adjustment compensates for any deviation from the normal value.



Hide 2.PERFORM BLIND SPOT MONITOR SENSOR INSTALLATION CONDITION INSPECTION

NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.



HINT:

The blind spot monitor sensor installation condition inspection is performed to confirm whether the sensor is perpendicular to the floor surface (+/-2.2°) by using a digital angle gauge, and that the sensor is 46 to 54° from the line parallel to the vehicle center line.


a.

Remove the rear bumper assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REMOVAL


b.

Place the digital angle gauge on a level (gradient within 1%) and perform zero-point adjustment as shown in the illustration.

E369196C04
0.958,1.063 1.125,1.063 1.125,1.063 1.708,1.396 true 0.958,1.781 1.125,1.781 1.125,1.781 1.708,1.531 true 5.792,0.458 5.625,0.458 5.625,0.458 5.292,1.042 true 4.719,0.479 4.885,0.479 4.885,0.479 5.135,1.063 true 1.958,2.417 2.135,2.625 0.177,0.208 10 false *c 5.073,2.167 5.313,2.375 0.24,0.208 10 false *d 0.698,0.979 1.156,1.177 0.458,0.198 10 false *a 0.719,1.698 1.177,1.896 0.458,0.198 10 false *b 4.552,0.396 5.01,0.594 0.458,0.198 10 false *b 5.906,0.365 6.365,0.563 0.458,0.198 10 false *a
*a (+) *b (-)
*c When Storing Zero Point *d After Storing Zero Point, Indicates 90° When Fully Horizontal



c.
B554824C01
0.75,1.75 1.698,1.75 true 2.438,1.292 2.833,1.167 true 1.115,2.896 1.552,2.302 true 0.521,1.667 0.698,1.833 0.177,0.167 10 true *a 2.875,1.104 3.052,1.271 0.177,0.167 10 true *1 0.917,2.927 1.094,3.094 0.177,0.167 10 true *b
*1 Blind Spot Monitor Sensor
*a Digital Angle Gauge
*b Outward Facing Surface


Set the digital angle gauge to the outward facing surface of the blind spot monitor sensor as shown in the illustration, and check that the perpendicular angle of the blind spot monitor sensor is within the permissible range.

HINT:
E367769C05
2.49,1.229 2.74,0.979 2.74,0.979 2.823,0.979 true 1.333,0.75 1.583,0.25 1.583,0.25 1.667,0.25 true 0.719,1.833 0.802,1.833 0.802,1.833 0.927,1.542 true 2.26,0.75 2.646,0.948 0.385,0.198 10 false *a 2.25,1.583 2.635,1.781 0.385,0.198 10 false *b 2.896,0.917 3.281,1.115 0.385,0.198 10 false *c 1.75,0.198 2.833,0.396 1.083,0.198 10 false *d 0.521,1.76 1.188,2.01 0.667,0.25 10 false *e
*a (+)
*b (-)
*c Horizontal Line
*d Digital Angle Gauge
*e Outward Facing Surface


The outward facing surface (installation angle) is positive (+) when it faces higher than horizontal.


Standard:
Item Allowable Range
Blind Spot Monitor Sensor RH (Master) +87.8 to +92.2°
Blind Spot Monitor Sensor LH (Slave) +87.8 to +92.2°



d.
E338854C05
0.698,2.073 1.073,2.396 true 2.135,3.125 2.51,3.448 true 0.479,2.75 0.917,2.74 true 1.813,3.458 2.115,3.688 true 0.083,0.094 0.396,0.25 0.313,0.156 12 false *A 1.104,2.948 1.417,3.104 0.313,0.156 10 false A 1.771,4.344 2.083,4.5 0.313,0.156 10 false *b 2.885,0.969 3.198,1.125 0.313,0.156 10 false *c 0.5,1.969 0.813,2.125 0.313,0.156 10 false *d 0.292,2.656 0.604,2.813 0.313,0.156 10 false *e 0.875,0.969 1.188,1.125 0.313,0.156 10 false *c 2.563,3.458 2.875,3.615 0.313,0.156 10 false *d 1.365,3.396 1.521,3.594 0.156,0.198 10 false y 1.667,0.167 1.979,0.365 0.313,0.198 10 false *a 2.146,3.708 2.458,3.865 0.313,0.156 10 false *e 1.927,2.083 2.094,2.281 0.167,0.198 10 true a
*A Vehicle Rear (LH)
*a Vehicle Front
*b Vehicle Rear
*c Line Parallel To The Vehicle Center Line
*d Stud Bolt
*e Stud Bolt Center Line


Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard:
Dimension Specified Value
a 108 mm (4.25 in.)
y 78 to 87 mm
(3.07 to 3.43 in.)

Degree Specified Value
A 46 to 54°


HINT:

If the results are not as specified, it is possible that the blind spot monitor sensor installation area (frame, stud bolt) is deformed, so make corrections as necessary.



e.

Install the rear bumper assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER>INSTALLATION