Home › Vehicle Interior › HEATING / AIR CONDITIONING › BLOWER UNIT
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0448154 BLOWER UNIT A

HEATING / AIR CONDITIONING  BLOWER UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
E458098N03
4.219,1.927 6.156,4.188 1.938,2.26 5.448,3.677 5.531,3.823 5.531,3.823 5.771,3.823 false 5.073,2.573 5.24,2.74 5.24,2.74 5.479,2.74 false 6.167,2.969 6.438,2.969 false 1.719,3.563 2.281,3.563 false 3.125,4.719 3.698,4.719 false 6.115,4.698 6.25,4.927 6.25,4.927 6.49,4.927 false 1.885,0.448 2.188,0.448 2.188,0.448 2.5,0.708 false 0.594,4.781 0.979,4.781 false 0.656,2.677 0.802,2.677 0.802,2.677 0.917,2.49 false 1.104,1.427 1.344,1.427 1.344,1.427 1.604,1.844 false 2.583,5.333 2.896,5.531 0.313,0.198 10 false x 3 1.219,2.042 1.531,2.24 0.313,0.198 10 false x 2 0.167,2.115 0.479,2.313 0.313,0.198 10 false x 4 1.375,3.458 1.531,3.656 0.156,0.198 10 false ● 1.542,0.344 1.698,0.542 0.156,0.198 10 false ● 5.531,2.646 5.844,2.844 0.313,0.198 10 false *1 5.823,3.729 6.135,3.927 0.313,0.198 10 false *2 0.448,4.646 0.729,5 0.281,0.354 18 false 8 1.688,0.292 1.969,0.646 0.281,0.354 18 false 7 6.792,4.781 7.073,5.135 0.281,0.354 18 false 6 6.74,2.823 7.021,3.177 0.281,0.354 18 false 4 3.771,4.563 4.052,4.917 0.281,0.354 18 false 4 1.531,3.417 1.813,3.771 0.281,0.354 18 false 3 0.49,2.521 0.771,2.875 0.281,0.354 18 false 2 0.917,1.271 1.198,1.625 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY 87130K - - -
2 COVER PLATE - (Click here) - -
3 NO. 1 BLOWER MOTOR SUB-ASSEMBLY PACKING 87127C (Click here) - -
4 BLOWER MOTOR WITH FAN SUB-ASSEMBLY 87103B - - -
5 AIR FILTER SUB-ASSEMBLY - (Click here) - -
6 AIR FILTER COVER PLATE 88899M (Click here) - -
7 NO. 1 COOLER UNIT PACKING 87429B (Click here) - -
8 NO. 2 COOLER UNIT DRAIN HOSE 88539C - - -

*1 CLEAN AIR FILTER *2 AIR FILTER CASE
● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 87130K 1.INSTALL NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

Hide 2.INSTALL COVER PLATE

a.
E456040C02
2.958,1.698 2.958,2.51 true 3.313,1.958 3.313,2.719 true 5.885,3.344 6.135,3.063 6.135,3.063 6.302,3.063 true 4,4.135 4.375,4.563 4.375,4.563 4.552,4.563 true 2.813,4.729 2.813,5.229 true 1.688,4.25 1.979,4.25 true 2.073,1.917 2.073,2.438 true 1.865,1.74 1.635,1.906 1.635,1.906 1.635,2.354 true 1.865,1.604 1.656,1.219 1.656,1.219 1.208,1.219 true 2.26,1.927 2.469,2.167 2.469,2.167 2.469,2.344 true 4.479,1.646 5.125,1.646 true 0.896,1.583 1.542,1.583 true 2.906,2.552 3.219,2.75 0.313,0.198 10 false *f 3.281,2.76 3.594,2.958 0.313,0.198 10 false *f 6.333,2.979 6.646,3.177 0.313,0.198 10 false *b 4.604,4.469 4.917,4.667 0.313,0.198 10 false *d 2.75,5.271 2.917,5.417 0.167,0.146 10 true *f 1.521,4.156 1.708,4.313 0.188,0.156 10 true *e 1.052,1.135 1.229,1.292 0.177,0.156 10 true *b 2.385,2.354 2.583,2.51 0.198,0.156 10 true *d 1.563,2.344 1.75,2.5 0.188,0.156 10 true *a 2.01,2.448 2.198,2.615 0.188,0.167 10 true *c 0.583,0.135 0.865,0.49 0.281,0.354 18 false i 5.167,1.552 5.354,1.708 0.188,0.156 10 true *e 0.688,1.5 0.875,1.656 0.188,0.156 10 true *e
*a Upper Fan Door Lever *b Fitting Surface of Upper Fan Door Lever
*c Lower Fan Door Lever *d Fitting Surface of Lower Fan Door Lever
*e Gears of cover plate and No. 1 blower damper servo sub-assembly aligned in standard position. *f Check Hole


i.

With the gears of the cover plate and No. 1 blower damper servo sub-assembly aligned in the standard position as shown in the illustration, attach the cover plate to the guide while moving the lever so that the point of engagement on the upper fan door lever and the point of engagement of the lower fan door lever enter the check holes.

NOTICE:

The upper fan door lever engagement cannot be checked from point of engagement with the check hole on the front surface of the cover plate. Therefore, look through the gap to check the engagement.




b.
E456038N01
0.365,0.063 0.646,0.417 0.281,0.354 18 false i

i.

Install the cover plate with the 4 screws.



Hide 87127C 3.INSTALL NO. 1 BLOWER MOTOR SUB-ASSEMBLY PACKING

Z101186

HINT:

Perform this procedure only when reusing the blower motor with fan sub-assembly.



Hide 87103B 4.INSTALL BLOWER MOTOR WITH FAN SUB-ASSEMBLY

Hide 5.INSTALL AIR FILTER SUB-ASSEMBLY

a.
E456041C02
0.188,0.156 6.938,5.563 6.75,5.406 0.198,3.208 6.938,3.208 false 2.438,1.104 2.729,0.729 2.729,0.729 3,0.729 true 1.063,2.115 1.344,2.115 1.344,2.115 1.615,2.333 true 0.802,0.26 0.938,0.563 0.135,0.302 18 false i 1.24,3.469 1.375,3.771 0.135,0.302 18 false ii 3.063,0.656 3.375,0.854 0.313,0.198 10 false *1 0.854,2.063 1.167,2.26 0.313,0.198 10 false *2
*1 Clean Air Filter *2 Air Filter Case
V113147

Install in this Direction - -


i.

Attach the guide and install the clean air filter to the air filter case as shown in the illustration.

NOTICE:

Align with the direction of the UP mark and install.



ii.

Install the air filter sub-assembly as shown in the illustration.

NOTICE:

Insert it with the arrow of the UP mark facing upward.




Hide 88899M 6.INSTALL AIR FILTER COVER PLATE

Z101186

NOTICE:

Insert it with the arrow of the UP mark facing upward.



Hide 87429B 7.INSTALL NO. 1 COOLER UNIT PACKING

a.
E456042C01
3.313,0.156 2.927,0.156 2.927,0.156 2.729,0.75 true 0.75,0.125 1.031,0.479 0.281,0.354 18 false i 1.979,0.781 2.292,0.979 0.313,0.198 10 false *a 3.354,0.094 3.667,0.292 0.313,0.198 10 true *b
*a Reference Line *b Wrap Portion
V113147

Apply in this Direction - -


i.

Remove the peeling paper on a new No. 1 cooling unit packing trying not to touch the adhesional surface and install it to the blower assembly.

NOTICE:
·

Check that any remaining No. 1 cooling unit packing has been completely removed from the blower assembly.

·

Attach so that there are no gaps in the entire circumference.

·

Start application from the reference line and follow the direction of the arrow.

·

Wrap and attach the No. 1 cooling unit packing. Do not cut it.





Hide 88539C 8.INSTALL NO. 2 COOLER UNIT DRAIN HOSE