Home › Vehicle Exterior › LIGHTING (EXT) › FRONT TURN SIGNAL LIGHT ASSEMBLY
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448276 FRONT TURN SIGNAL LIGHT ASSEMBLY A

LIGHTING (EXT)  FRONT TURN SIGNAL LIGHT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E457480N01
0.385,1.583 0.875,1.583 false 5.073,1.906 5.073,1.573 false 0.219,1.448 0.5,1.802 0.281,0.354 18 false 1 5.021,1.958 5.302,2.313 0.281,0.354 18 false 2 6.208,1.104 6.521,1.302 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT BUMPER ASSEMBLY - - - -
2 FRONT TURN SIGNAL LIGHT ASSEMBLY LH 81520 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front turn signal light assembly LH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Front bumper assembly (Including removal and installation)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA Parking assist- sensor system

·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Front television camera view adjustment Panoramic view monitor system (Click here)
Front television camera assembly, front bumper assembly or radiator grille
·

Television camera view adjustment

HINT:

Replacement or removal and installation of 2 or more parts



Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 1.REMOVE FRONT BUMPER ASSEMBLY

Hide 81520 2.REMOVE FRONT TURN SIGNAL LIGHT ASSEMBLY LH

a.
E462978C01
0.146,0.167 6.979,1.865 6.833,1.698 0.25,0.229 0.531,0.583 0.281,0.354 18 false i 4.198,2.135 4.479,2.49 0.281,0.354 18 true ii 2.458,3.26 2.74,3.615 0.281,0.354 18 true iii 4.198,3.323 4.479,3.677 0.281,0.354 18 true iii 0.5,0.365 0.875,0.604 0.375,0.24 12 true *A 3.948,0.375 4.323,0.615 0.375,0.24 12 true *B
*A w/o Adaptive High Beam System *B w/ Adaptive High Beam System
V100135

Connector
V100136

Clip
V100137

Screw - -