Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM37H0E _58 Vehicle Interior _095306 LIGHTING (INT) _0448415 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  ACC Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E458933E01
0.25,3.01 1.938,3.208 1.688,0.198 10 false *1: for LHD 0.25,3.302 1.938,3.5 1.688,0.198 10 false *2: for RHD 2.646,2.875 5.323,3.25 2.677,0.375 10 false Driver Side Junction Block Assembly 5.427,2.99 7.094,3.385 1.667,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 5.438,2.823 6.167,3.229 0.729,0.406 10 false A 5.698,0.74 6.427,1.146 0.729,0.406 10 false ACC 4.385,1.031 5.115,1.438 0.729,0.406 10 false ACC D 3.573,1.604 4.302,2.01 0.729,0.406 10 false ACC D 2.615,2.115 3.344,2.521 0.729,0.406 10 false 4D 2.219,2.115 2.948,2.521 0.729,0.406 10 false 4D 2.25,1.896 2.979,2.302 0.729,0.406 10 false 7 0.26,0.823 1.646,1.417 1.385,0.594 10 false from Auxiliary Battery 2.208,2.333 2.938,2.74 0.729,0.406 10 false *2 2.208,1.552 2.938,1.958 0.729,0.406 10 false *2 2.635,1.552 3.365,1.958 0.729,0.406 10 false *1 2.635,2.323 3.365,2.729 0.729,0.406 10 false *1 2.656,1.896 3.385,2.302 0.729,0.406 10 false 6 2.615,1.333 3.344,1.74 0.729,0.406 10 false 4D 2.219,1.333 2.948,1.74 0.729,0.406 10 false 4D 2.615,1.125 3.344,1.531 0.729,0.406 10 false 17 2.208,1.115 2.938,1.521 0.729,0.406 10 false 18 2.625,0.865 3.354,1.271 0.729,0.406 10 false 4K 5.385,1.99 6.115,2.396 0.729,0.406 10 false 11 5.385,0.729 6.115,1.135 0.729,0.406 10 false 30 5.719,2.125 6.448,2.531 0.729,0.406 10 false GND1 2.656,0.635 3.385,1.042 0.729,0.406 10 false 1 0.198,1.333 1.583,1.927 1.385,0.594 10 false from Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC (ENTRY AND START SYSTEM [for Start Function])
a.

Check for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
OK:

Entry and start system (for Start Function) DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Ignition switch ACC signal OFF or ON OFF: Ignition switch off
ON: Ignition switch ACC
"ON" is also displayed for this item when the ignition switch is ON.
Body Electrical > Main Body > Data List
Tester Display
ACC SW
50003 123 31
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.
E361158C09
1.458,0.667 1.99,0.896 0.531,0.229 1.469,2.615 2,2.844 0.531,0.229 0.125,0.156 0.438,0.313 0.313,0.156 10 false *a 1.656,2.656 1.969,2.813 0.313,0.156 10 false 4K 1.646,0.719 1.958,0.875 0.313,0.156 10 false 4D
*a Front view of wire harness connector
(to Driver Side Junction Block Assembly)


Disconnect the driver side junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
4D-6 - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
4D-7 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
4K-1 - Body ground Ignition switch off 11 to 14 V
4D-17 - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
4K-1 - Body ground Ignition switch off 11 to 14 V
4D-18 - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

E361156C11
1.771,0.229 2.25,0.438 0.479,0.208 5.49,0.25 5.969,0.458 0.479,0.208 3.271,1.823 3.75,2.031 0.479,0.208 4.979,2.375 5.271,2.042 5.271,2.042 5.448,2.042 true 2.469,2 2.646,2 2.646,2 2.969,2.385 true 5.646,0.271 5.958,0.469 0.313,0.198 10 false 4K 1.917,0.25 2.229,0.448 0.313,0.198 10 false 4D 3.458,1.833 3.771,2.031 0.313,0.198 10 false A 5.521,1.948 6.01,2.167 0.49,0.219 10 false ACC 0.208,0.125 0.521,0.323 0.313,0.198 10 false *a 2.073,1.927 2.563,2.146 0.49,0.219 10 false GND1
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
4K-1 - A-30 (ACC) Auxiliary battery not connected to 4D-17 and 4D-6 10 kΩ or higher
Auxiliary battery positive (+) → 4D-17
Auxiliary battery negative (-) → 4D-6
Below 1 Ω
4D-6 - A-11 (GND1) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
4K-1 - A-30 (ACC) Auxiliary battery not connected to 4D-18 and 4D-7 10 kΩ or higher
Auxiliary battery positive (+) → 4D-18
Auxiliary battery negative (-) → 4D-7
Below 1 Ω
4D-7 - A-11 (GND1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY