Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU
RM37H0E _57 Power Source / Network _095301 POWER DISTRIBUTION _0448151 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E460129N01
4.948,0.552 5.198,0.552 false 6.469,0.24 6.844,0.24 false 4.906,2.219 5.156,2.542 5.156,2.542 5.583,2.542 false 3.948,3.281 4.198,3.604 4.198,3.604 4.625,3.604 false 1.802,4.156 2.052,4.479 2.052,4.479 2.479,4.479 false 1.177,0.688 1.479,0.688 1.479,0.688 1.708,0.906 false 5.865,1.177 6.323,1.375 0.458,0.198 10 false x 2 3.781,3.729 4.24,3.927 0.458,0.198 10 false x 2 6.313,0.083 6.479,0.396 0.167,0.313 18 false 1 2.531,4.323 2.698,4.635 0.167,0.313 18 false 2 4.688,3.427 4.854,3.74 0.167,0.313 18 false 3 5.635,2.385 5.802,2.698 0.167,0.313 18 false 4 0.979,0.542 1.146,0.854 0.167,0.313 18 false 5 4.708,0.427 4.875,0.74 0.167,0.313 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 73900 - - -
3 AIR DUCT SUB-ASSEMBLY - - - -
4 NO. 2 HEATER TO REGISTER DUCT 55844 - - -
5 NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY 55308B - - -
6 DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU - (Click here) - -

E460130N01
3.635,1.573 3.958,1.573 false 1.5,1.698 1.823,1.698 false 6.292,1.438 6.615,1.438 false 1.885,1.594 2.198,1.792 0.313,0.198 10 false *1 6.677,1.292 6.958,1.646 0.281,0.354 18 false 7 4.396,1.427 4.677,1.781 0.281,0.354 18 false 8 4.26,1.49 4.573,1.688 0.313,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

7 WIRING HARNESS CLAMP BRACKET 82715 - - -
8 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 89221 (Click here) - -

*1 DRIVER SIDE JUNCTION BLOCK ASSEMBLY - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Main body ECU (multiplex network body ECU) Code registration (Immobiliser system)
·

Wireless function

·

Smart function

·

Does not change to on (READY)


See Service Bulletin for the registration method.

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

Do not remove the main body ECU (multiplex network body ECU) except when replacing it.

·

When removing the main body ECU (multiplex network body ECU), always replace it with a new one.




Hide 73900 2.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55308B 5.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Hide 6.REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

a.

for RHD:

E450292N01
0.281,0.052 0.563,0.406 0.281,0.354 18 false i

i.

Remove the 2 nuts and disconnect the ECU.



b.
E456008N01
0.344,0.083 0.625,0.438 0.281,0.354 18 false i

i.

Remove the 2 nuts.



c.
E456009C01
0.542,0.115 0.677,0.365 0.135,0.25 18 true i 4.323,0.156 4.51,0.406 0.188,0.25 18 true ii
V113147

Remove in this Direction - -


i.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.


ii.

Disconnect the 5 connectors.



d.
E456010C01
0.625,0.188 0.906,0.542 0.281,0.354 18 false i 4.25,0.229 4.531,0.583 0.281,0.354 18 false ii
V113147

Remove in this Direction - -


i.

Detach the clamp.


ii.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw, disconnect the 2 lever connectors and remove the driver side junction block assembly with main body ECU.



Hide 82715 7.REMOVE WIRING HARNESS CLAMP BRACKET

a.
E456011


Hide 89221 8.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E450297C07
0.615,1.667 0.615,1.167 0.615,1.167 0.781,1.167 true 0.958,1.24 1.188,1.24 true 2.667,3.375 2.885,3.375 2.885,3.375 3.135,2.885 true 0.563,1.698 0.875,1.896 0.313,0.198 10 false *2 1.25,1.188 1.563,1.385 0.313,0.198 10 false *1 1.75,0.25 2,0.615 0.25,0.365 18 false i 6.458,1.531 6.656,1.833 0.198,0.302 18 false ii 2.385,2.365 2.635,2.729 0.25,0.365 18 false iv 5.385,0.146 5.656,0.406 0.271,0.26 18 false iii 2.479,3.302 2.792,3.5 0.313,0.198 10 false *a
*1 Driver Side Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)
*a Rib - -
V113147

Rotate in this Direction
V113148

Remove in this Direction
V100135

Push in this Direction
V100136

Horizontally Insert a Thin-bladed Screwdriver


i.

Press the claw of the driver side junction block assembly as shown in the illustration and release the lock of the main body ECU (multiplex network body ECU).


ii.

With the lock released, insert a screwdriver with its tip wrapped with protective tape horizontally in between the main body ECU (multiplex network body ECU) and the driver side junction block assembly.

NOTICE:

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).



iii.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:
·

Do not pry and lift with the screwdriver.

·

Replace the driver side junction block assembly or the main body ECU (multiplex network body ECU) when the connector terminal, locking section or case is damaged or deformed.




iv.

Lift up the rib of the main body ECU (multiplex network body ECU) and slide the main body ECU (multiplex network body ECU) to remove it as shown in the illustration.

NOTICE:

Do not touch the ECU connector terminal with your fingers.