Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM37H0E _58 Vehicle Interior _095306 LIGHTING (INT) _0448415 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Auto Cut Circuit  


DESCRIPTION

When the battery saving control operates, the main body ECU (multiplex network body ECU) controls the operation of the DOME CUT D relay that is built into the driver side junction block assembly to turn off the interior lights.

WIRING DIAGRAM

E462628E01
1.115,1.354 3.865,1.552 2.75,0.198 10 false to Interior Lights 1.104,2.115 3.854,2.313 2.75,0.198 10 false to Interior Lights 0.823,2.844 3.573,3.042 2.75,0.198 10 false from Auxiliary Battery 2.938,1.365 5.688,1.563 2.75,0.198 10 false 4D 2.938,2.125 5.688,2.323 2.75,0.198 10 false 4A 2.948,2.875 5.698,3.073 2.75,0.198 10 false 4K 2.969,1.188 5.719,1.385 2.75,0.198 10 false 5 2.979,1.938 5.729,2.135 2.75,0.198 10 false 3 2.979,2.688 5.729,2.885 2.75,0.198 10 false 1 3.427,3.01 6.177,3.208 2.75,0.198 10 false DOME D 4.25,3.625 7,3.823 2.75,0.198 10 false DOME CUT D 3.646,4.188 4.885,4.885 1.24,0.698 10 false Driver Side Junction Block Assembly 5.302,4.365 6.948,5.156 1.646,0.792 10 false Main Body ECU (Multiplex Network Body ECU) 5.302,4.188 6.948,4.979 1.646,0.792 10 false A 5.385,3.219 7.031,4.01 1.646,0.792 10 false DOMR 5.073,3.24 6.719,4.031 1.646,0.792 10 false 23

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME CUT D relay ON or OFF When performing this Active Test, turn all the interior lights on.
·

OFF: DOME CUT D relay on (interior lights turn on)

·

ON: DOME CUT D relay off (interior lights turn off)


Body Electrical > Main Body > Active Test
Tester Display
Relay for Interior Light Auto Cut Function
50004 123 66
OK:

All of the interior lights turn off when ON is selected.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BATTERY)
2.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BATTERY)
a.
E364057C09
1.469,0.375 1.958,0.594 0.49,0.219 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.646,0.396 1.958,0.552 0.313,0.156 10 false 4K
*a Front view of wire harness connector
(to Driver Side Junction Block Assembly)


Disconnect the driver side junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4K-1 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

E361207C06
1.885,0.156 2.427,0.385 0.542,0.229 4.75,0.281 5.292,0.51 0.542,0.229 3.25,1.698 3.792,1.927 0.542,0.229 4.25,2.188 4.573,1.802 4.573,1.802 4.719,1.802 true 0.135,0.063 0.448,0.219 0.313,0.156 10 false *a 4.958,0.313 5.24,0.542 0.281,0.229 10 false 4K 2.073,0.177 2.354,0.406 0.281,0.229 10 false 4D 3.469,1.719 3.75,1.948 0.281,0.229 10 false A 4.781,1.688 5.24,1.885 0.458,0.198 10 false DOMR
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4K-1 - 4D-5 Auxiliary battery not connected to 4K-1 and A-23 (DOMR) 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4D-5 - Auxiliary battery negative (-) terminal Auxiliary battery positive (+) → 4K-1
Auxiliary battery negative (-) → A-23 (DOMR)
11 to 14 V
Auxiliary battery not connected to 4K-1 and A-23 (DOMR) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY