Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448416 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects ambient light. The sensor creates an electrical signal based on the amount of light detected, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B1244 Light Sensor Circuit Malfunction
Detection condition:

Ignition switch ON


Malfunction status:

Either of the following conditions is met:

-

Malfunction in automatic light control sensor

-

Open or short in automatic light control sensor circuit



Malfunction duration:

5 seconds or more


·

Harness or connector

·

Automatic light control sensor

·

Main body ECU (multiplex network body ECU)


Main Body A -

WIRING DIAGRAM

E364105E17
5.208,3.635 6.875,4.021 1.667,0.385 10 false D11 5.208,2.729 6.406,3.031 1.198,0.302 10 false CLTE 5.208,2.104 6.406,2.406 1.198,0.302 10 false CLTS 5.198,0.969 6.396,1.271 1.198,0.302 10 false CLTB 4.896,2 6.094,2.302 1.198,0.302 10 false 24 4.896,0.958 6.094,1.26 1.198,0.302 10 false 23 4.906,2.729 6.104,3.031 1.198,0.302 10 false 25 2.021,2.719 3.219,3.021 1.198,0.302 10 false 2 2.021,1.99 3.219,2.292 1.198,0.302 10 false 4 2.031,0.927 3.229,1.229 1.198,0.302 10 false 1 1.51,2.708 2.708,3.01 1.198,0.302 10 false CLTE 1.5,1.969 2.698,2.271 1.198,0.302 10 false CLTS 1.49,0.958 2.688,1.26 1.198,0.302 10 false CLTB 0.229,3.625 1.427,3.927 1.198,0.302 10 false D13 0.229,3.771 2.875,3.958 2.646,0.188 10 false Automatic Light Control Sensor 5.208,3.802 6.875,4.188 1.667,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 6.198,0.656 6.635,0.948 0.438,0.292 10 false IG

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 5 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B1244 is not output A
B1244 is output B



Post-procedure1

a.

None



A

B

3.READ VALUE USING GTS
3.READ VALUE USING GTS
a.

According to the display on the GTS, read the Data List and check that the value of Light Sensor Illuminance changes while performing the following:

i.

Turn the light control switch to the AUTO position.


ii.

Cover the automatic light control sensor with an opaque object.


iii.

Slowly move the opaque object to uncover and then cover the automatic light control sensor.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Light Sensor Illuminance Light control sensor illuminance 0 to 8191 lx Value is output according to ambient light level -
Body Electrical > Main Body > Data List
Tester Display
Light Sensor Illuminance
50003 123 279
OK:

The value changes according to the amount the automatic light control sensor is covered.




Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.CHECK AUTOMATIC LIGHT CONTROL SENSOR
4.CHECK AUTOMATIC LIGHT CONTROL SENSOR
a.

Using an oscilloscope, check the waveform.

E364129C07
2,0.208 2.552,0.427 0.552,0.219 3.188,2.188 2.927,2.188 2.927,2.188 2.333,1.573 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 3.99,0.188 4.302,0.344 0.313,0.156 10 false *b 6.313,1.792 6.625,1.948 0.313,0.156 10 false GND 3.26,2.083 3.708,2.313 0.448,0.229 10 false CLTS 2.146,0.24 2.594,0.469 0.448,0.229 10 false D11
*a Component with harness connected
(Main Body ECU [Multiplex Network Body ECU])
*b Waveform


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(D11)Location & Routing

Click Connector(D11)Instrument Panel>Instrument Panel Wire>Main Body ECU

D11-24 (CLTS) - Body ground Ignition switch ON, material which blocks light used to cover and then uncover top of automatic light control sensor 2 V/DIV., 10 ms./DIV. Pulse generation


HINT:

The communication waveform changes according to the surrounding brightness.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

5.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
5.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Pre-procedure1

a.
E364086C47
0.229,0.99 0.635,1.24 0.406,0.25 2.635,1.677 2.448,1.677 2.448,1.677 1.917,1.292 true 2.302,2.01 2.115,2.01 2.115,2.01 1.708,1.271 true 0.208,0.135 0.521,0.292 0.313,0.156 10 false *a 0.313,1.031 0.625,1.188 0.313,0.156 10 false D11 2.677,1.563 3.073,1.719 0.396,0.156 10 false CLTB 2.344,1.906 2.74,2.063 0.396,0.156 10 false CLTE
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Disconnect the D13 automatic light control sensor connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D11)Location & Routing

Click Connector(D11)Instrument Panel>Instrument Panel Wire>Main Body ECU

D11-23 (CLTB) - D11-25 (CLTE) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - AUTOMATIC LIGHT CONTROL SENSOR)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - AUTOMATIC LIGHT CONTROL SENSOR)

Pre-procedure1

a.

Disconnect the D11 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the D13 automatic light control sensor connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D11,D13)Location & Routing

Click Connector(D11)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(D13)Instrument Panel>Instrument Panel Wire>Automatic Light Control Sensor

D11-23 (CLTB) - D13-1 (CLTB) Always Below 1 Ω
D11-24 (CLTS) - D13-4 (CLTS) Always Below 1 Ω
D11-25 (CLTE) - D13-2 (CLTE) Always Below 1 Ω
D11-23 (CLTB) or D13-1 (CLTB) - Body ground Always 10 kΩ or higher
D11-24 (CLTS) or D13-4 (CLTS) - Body ground Always 10 kΩ or higher
D11-25 (CLTE) or D13-2 (CLTE) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE AUTOMATIC LIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR