Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0448454 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B424476E56
0.823,0.156 1.688,0.375 0.865,0.219 10 false from Auxiliary Battery 2.333,1.865 2.948,2.063 0.615,0.198 10 false HORN 1.104,1.094 1.719,1.292 0.615,0.198 10 false HORN 6.115,0.844 6.729,1.042 0.615,0.198 10 false HORN 0.969,2.281 3.76,2.677 2.792,0.396 10 false NO. 1 Front Compartment Relay Block 2.573,4.76 3.708,5.125 1.135,0.365 10 false Low Pitched Horn Assembly 4.198,4.75 5.344,5.125 1.146,0.375 10 false High Pitched Horn Assembly 4.438,1.917 6.052,2.323 1.615,0.406 10 false Driver Side Junction Block Assembly 5.375,3.396 7.052,3.927 1.677,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 2.021,0.844 2.24,1.042 0.219,0.198 10 false 1 2.031,1.448 2.25,1.646 0.219,0.198 10 false 3 2.938,0.833 3.156,1.031 0.219,0.198 10 false 2 2.938,1.448 3.156,1.646 0.219,0.198 10 false 5 2.26,4.5 2.479,4.698 0.219,0.198 10 false 1 3.875,4.521 4.094,4.719 0.219,0.198 10 false 1 2.594,4.583 2.948,4.781 0.354,0.198 10 false A38 4.198,4.573 4.552,4.771 0.354,0.198 10 false A36 4.792,4.031 7.104,4.25 2.313,0.219 10 false to Steering Pad Switch Assembly 5.865,0.823 6.219,1.021 0.354,0.198 10 false 28 5.365,3.208 5.719,3.406 0.354,0.198 10 false A 6.74,1.021 7.094,1.219 0.354,0.198 10 false IC 4.563,0.573 5.292,0.76 0.729,0.188 10 false 16*1 4.625,0.948 4.979,1.146 0.354,0.198 10 false 4F 4.625,1.24 4.979,1.438 0.354,0.198 10 false 27 4.615,1.448 4.969,1.646 0.354,0.198 10 false 4A 4.563,0.74 5.292,0.927 0.729,0.188 10 false 28*2 0.219,5.083 1.531,5.281 1.313,0.198 10 false *1: for LHD 0.188,5.385 1.5,5.583 1.313,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK HORNS OPERATION
a.

Press the horn switch and check if the horns sound.


Result:
Proceed to
Horns sound
Horns do not sound



Horns sound

2.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

Horns do not sound

2.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.
B468454C01
1.615,1.677 2,1.927 0.385,0.25 1.573,0.385 1.958,0.635 0.385,0.25 2.583,1.25 2.667,0.813 true 2.344,1.25 2.583,1.25 false 1.719,0.417 1.875,0.615 0.156,0.198 10 false A 1.729,1.719 2.01,1.938 0.281,0.219 10 false 4F 0.198,0.115 0.354,0.313 0.156,0.198 10 false *a 1.927,1.177 2.542,1.375 0.615,0.198 10 false HORN
*a Component without harness connected
(Driver Side Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
4F-16 - A-28 (HORN) Always Below 1 Ω


Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
4F-28 - A-28 (HORN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY