The theft warning siren assembly has an internal battery. If the vehicle battery cable is disconnected or any of the communication lines are open, the theft warning siren assembly detects this and sounds its siren.
Although the theft warning siren assembly usually sounds by receiving a signal from the main body ECU (multiplex network body ECU), the theft warning siren assembly can sound by its internal battery in case the vehicle battery cable is disconnected.
The main body ECU (multiplex network body ECU) sends an arming signal to the theft warning siren assembly while transferring to the armed state, and it also sends a disarming signal to the siren while switching to the disarmed state. Also, the main body ECU (multiplex network body ECU) can cause the theft warning siren assembly to sound by sending an alarm signal during the alarm sounding state.
If the theft warning siren assembly or main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Security Horn2 | Theft warning siren assembly | ON or OFF | - |
| Tester Display |
|---|
| Security Horn2 |
The theft warning siren assembly sounds and stops correctly when operated through the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the theft warning siren assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G50)Location & Routingewd_type=routing;type=c;code=G50 Click Connector(G50)Body>Floor Wire / No. 3 Floor Wire>Theft Warning Siren Assemblyewd_type=component;type=c;code=G50;pinno=3 |
||
| G50-3 (+B) - Body ground | Ignition switch off | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G50)Location & Routingewd_type=routing;type=c;code=G50 Click Connector(G50)Body>Floor Wire / No. 3 Floor Wire>Theft Warning Siren Assemblyewd_type=component;type=c;code=G50;pinno=1 |
||
| G50-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G50 theft warning siren assembly connector.
Disconnect the D14 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G50,D14)Location & Routingewd_type=routing;type=c,c;code=G50,D14 Click Connector(G50)Body>Floor Wire / No. 3 Floor Wire>Theft Warning Siren Assemblyewd_type=component;type=c;code=G50;pinno=2 Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECUewd_type=component;type=c;code=D14;pinno=12 |
||
| G50-2 (CONT) - D14-12 (SSCL) | Always | Below 1 Ω |
| G50-2 (CONT) or D14-12 (SSCL) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the theft warning siren assembly with a new or normally functioning one.
Refer to the Service Bulletin.
Check the operation of the theft warning siren assembly function.
Theft warning siren assembly function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG