Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)
RM37H0E _55 Steering _095770 STEERING COLUMN _0449635 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
C447799N01
5.229,1.76 5.333,1.583 5.333,1.583 5.5,1.583 true 4.604,0.75 4.854,0.75 true 5.354,2.229 5.5,2.417 5.5,2.417 5.667,2.417 false 5.75,2.313 6.208,2.51 0.458,0.198 10 false ●*1 5.854,1.448 6.125,1.74 0.271,0.292 18 false 1 4.927,0.615 5.198,0.906 0.271,0.292 18 false 2 5.438,2.094 5.667,2.281 0.229,0.188 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY 45020B (Click here) - -
2 MULTIPLEX TILT AND TELESCOPIC ECU 89227 - - -

*1 STEERING LOCK SET BOLT - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

Do not drop the steering lock actuator or upper bracket assembly, strike it with tools or subject it toimpacts.

·

If the steering lock actuator or upper bracket assembly is subjected to an impact, replace it with a newone.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45020B 1.REMOVE STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY

a.
C447800C01
4.396,0.677 4.5,0.583 4.5,0.583 4.583,0.583 true 3.667,0.25 3.75,0.25 3.75,0.25 3.823,0.531 true 0.354,0.01 0.635,0.365 0.281,0.354 18 false i 2.813,0.021 3.281,0.302 0.469,0.281 18 true ii 5.344,0.021 5.948,0.344 0.604,0.323 18 true iii, iv 4.635,0.5 4.948,0.698 0.313,0.198 10 false *a 3.354,0.177 3.854,0.458 0.5,0.281 10 false SST
*a Center of the steering lock set bolt - -


i.

Secure the steering column assembly in a vise between aluminum plates.

NOTICE:
·

Do not overtighten the vise.

·

Do not clamp the steering lock actuator or upper bracket assembly in the vise.




ii.

Using SST, strike a punch mark for drilling in the center of the steering lock set bolt.

SST
09622-00010  

NOTICE:

When striking the punch mark, in order to prevent impact force from being applied to the steering lock actuator or upper bracket assembly, do not use a normal center punch.



iii.

Using a drill, drill a hole in 2 steering lock set bolts and insert a screw extractor.


iv.

Using the screw extractor, remove the 2 steering lock set bolts and steering lock actuator or upper bracket assembly.

NOTICE:

Push in the screw extractor by hand, and do not strike it with tools, etc.




Hide 89227 2.REMOVE MULTIPLEX TILT AND TELESCOPIC ECU

a.
C447801N01
0.083,0.083 0.365,0.438 0.281,0.354 18 false i

i.

Disengage the 2 claws and guide to remove the multiplex tilt and telescopic ECU from the steering column assembly.