Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449816 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A2  Open in Front Passenger Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for front passenger door) (electrical key antenna) at intervals of 0.25 seconds. For the front door outside handle assembly (for front passenger door) (electrical key antenna) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the front passenger door at intervals of 0.25 seconds. DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) (electrical key antenna) (between terminals CLG2 and ANT1, or terminals CG2B and ANT2).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B27A2 Open in Front Passenger Side Electrical Antenna Circuit An open is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) (CLG2 - ANT1, CG2B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

Front door outside handle assembly (for front passenger door)

·

Harness or connector


Entry&Start A
DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for front passenger door -

Related Data List and Active Test
DTC No. Data List and Active Test
B27A2 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B601016E04
1.302,0.75 1.917,0.948 0.615,0.198 10 false ANT1 1.302,1.896 1.917,2.094 0.615,0.198 10 false ANT2 1.771,0.74 1.927,0.938 0.156,0.198 10 false 6 1.781,1.896 1.938,2.094 0.156,0.198 10 false 4 4.938,0.865 5.333,1.063 0.396,0.198 10 false G37 4.938,2.01 5.25,2.208 0.313,0.198 10 false G37 4.969,0.646 5.281,0.844 0.313,0.198 10 false 15 4.969,1.802 5.281,2 0.313,0.198 10 false 14 5.302,0.75 5.917,0.948 0.615,0.198 10 false CLG2 5.302,1.896 5.917,2.094 0.615,0.198 10 false CG2B 5.833,1.385 6.146,1.583 0.313,0.198 10 false IC 0.479,2.521 1.292,2.719 0.813,0.198 10 false E4*1, E22*2 0.49,2.677 2.792,3.385 2.302,0.708 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 5.104,2.531 6.635,3.49 1.531,0.958 10 false Certification ECU (Smart Key ECU Assembly) 6.479,2.01 6.938,2.208 0.458,0.198 10 false D86 6.531,1.802 6.844,2 0.313,0.198 10 false 18 6.25,2 6.406,2.198 0.156,0.198 10 false E 3.427,2.875 4.417,3.104 0.99,0.229 10 false *1: for LHD 3.427,3.188 4.417,3.417 0.99,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

Pre-procedure 1

a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the E4*1 or E22*2 front door outside handle assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



procedure 1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,E4)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(E4)Body>Front Door Wire LH / Front Door Wire RH>Front Door Outside Handle Assembly RH

G37-15 (CLG2) - E4-6 (ANT1) Always Below 1 Ω
G37-14 (CG2B) - E4-4 (ANT2) Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,E22)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(E22)Body>Front Door Wire LH / Front Door Wire RH>Front Door Outside Handle Assembly LH

G37-15 (CLG2) - E22-6 (ANT1) Always Below 1 Ω
G37-14 (CG2B) - E22-4 (ANT2) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure 1

d.

Reconnect the G37 certification ECU (smart key ECU assembly) connector.



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))
B473188C45
3.271,0.583 3.635,0.792 0.365,0.208 4.5,0.583 4.865,0.792 0.365,0.208 3.479,2.26 3.219,1.365 true 2.865,2.292 3.135,1.385 true 5.635,2.167 5.208,1.479 true 0.177,0.125 0.469,0.323 0.292,0.198 10 false *a 3.333,0.594 3.708,0.781 0.375,0.188 10 false G37 4.563,0.594 4.865,0.792 0.302,0.198 10 false D86 2.552,2.323 3.021,2.521 0.469,0.198 10 false CLG2 3.458,2.313 3.938,2.49 0.479,0.177 10 false CG2B 5.656,2.177 5.865,2.375 0.208,0.198 10 false E 0.698,2.719 0.99,2.917 0.292,0.198 10 false *b 4.104,2.708 4.354,2.906 0.25,0.198 10 false *c 4.01,3.563 4.406,3.76 0.396,0.198 10 false GND 0.594,3.552 0.979,3.75 0.385,0.198 10 false GND 0.698,4.708 0.99,4.906 0.292,0.198 10 false *d 4.104,4.708 4.396,4.906 0.292,0.198 10 false *e 4,5.573 4.354,5.771 0.354,0.198 10 false GND 0.583,5.573 0.917,5.792 0.333,0.219 10 false GND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Waveform 2 *d Waveform 3
*e Waveform 4 - -


a.

Using an oscilloscope, check the waveform.

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G37,D86)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

G37-15 (CLG2) - D86-18 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
G37-15 (CLG2) - D86-18 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 100 ms/DIV. Pulse generation
(See waveform 2)
G37-14 (CG2B) - D86-18 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 3)
G37-14 (CG2B) - D86-18 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 100 ms/DIV. Pulse generation
(See waveform 4)


HINT:

*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)