| *A | for Driver Side | *B | for Front Passenger Side |
| *C | w/ Seat Memory Switch | - | - |
| *A | For Driver Side | *B | For Front Passenger Side |
| *1 | Hole Plug | - | - |
|
MP grease | - | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door disassembly are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. | - |
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
When removing the front door glass sub-assembly LH, move the front door glass sub-assembly LH to the lowest position before disconnecting the auxiliary battery negative (-) terminal.
1. PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
69284C
3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Using moulding remover A, detach the claws and remove the front door inside handle bezel plug.
4.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
|
Remove in this Order | - | - |
Using moulding remover A, detach the guides, claws and clips as shown in the illustration and remove the power window regulator master switch assembly with front door armrest base panel.
Disconnect the connector.
5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
|
Remove in this Order | - | - |
Using moulding remover A, detach the guides, claws and clips as shown in the illustration and remove the power window regulator switch assembly with front door armrest base panel.
Disconnect the connector.
67602
6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
|
Place Hands Here |
|
Remove in this Order |
|
Remove in this Direction | - | - |
Remove the 3 screws.
Place your hand at the position shown in the illustration, detach the clip.
Pull the front door trim board sub-assembly shown in the illustration, detach the claws and guides and remove the front door trim board sub-assembly from the front door panel.
|
Place Hands Here |
|
Remove in this Direction |
Detach the clamps and disconnect the open lever front door lock remote control cable from the front door inside handle sub-assembly.
Detach the claws and clamps, disconnect the lock/unlock knob front door inside locking cable.
Disconnect the connectors.
84927C
8.REMOVE SEAT MEMORY SWITCH (w/ Seat Memory Switch)
81080V
9.REMOVE NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY
69206B
10.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
|
Remove in this Direction | - | - |
67492A
11.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
|
Remove in this Direction | - | - |
68172A
12.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
|
Remove in this Direction | - | - |
Using a clip remover with its tip wrapped in protective tape, detach the clips.
Detach the guide and turn over the front door glass weatherstrip inner partially.
Remove the front door glass inner weatherstrip with front door belt rear seal.
68195B
13.REMOVE FRONT DOOR BELT REAR SEAL
|
Remove in this Direction | - | - |
68193C
14.REMOVE FRONT DOOR BELT FRONT SEAL
|
Remove in this Direction | - | - |
89223
16.REMOVE MULTIPLEX NETWORK FRONT DOOR ECU
Disconnect the connectors.
Detach the clamp.
Be sure to replace the clamps with a new one when disconnecting, for they are non-reusable part.
Remove the 2 screws and remove the multiplex network fornt door ECU.
Remove the 2 grommets.
17.REMOVE HOLE PLUG
67834
18.REMOVE FRONT DOOR NO. 2 SERVICE HOLE COVER
67832
20.REMOVE FRONT DOOR SERVICE HOLE COVER
|
Remove in this Direction | - | - |
Turn the service hole cover clip 45° to remove the 3 service hole cover clips as shown in the illustration.
Using a clip remover with its tip wrapped in protective tape, detach the clips and remove the front door service hole cover.
Pull out the front door lock remote control cable assembly and front door inside locking cable assembly from the front door service hole cover as shown in the illustration.
68102
22.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Connect the multiplex network front door ECU.
for Driver Side:
1. Connect the power window regulator master switch assembly with front door armrest base panel.
for Front Passenger Side:
1. Connect the power window regulator switch assembly with front door armrest base panel.
Connect the connectors to temporarily install the front door trim board sub-assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch on.
Move the door glass until the bolts appear in the service holes.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an SRS part is accidentally deployed, it may cause a serious injury.
Disconnect the connectors to remove the front door trim board sub-assembly.
For Driver Side:
1. Disconnect the power window regulator master switch assembly with front door armrest base panel.
For Front Passenger Side:
1. Disconnect the power window regulator switch assembly with front door armrest base panel.
1. Disconnect the multiplex network front door ECU.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an SRS part is accidentally deployed, it may cause a serious injury.
Disconnect the connectors to remove the front door trim board sub-assembly.
For Driver Side:
1. Disconnect the power window regulator master switch assembly with front door armrest base panel.
For Front Passenger Side:
1. Disconnect the power window regulator switch assembly with front door armrest base panel.
1. Disconnect the multiplex network front door ECU.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the 2 bolts.
Remove the front door glass sub-assembly as shown in the illustration.
Do not damage the front door glass.
68151C
23.REMOVE FRONT DOOR GLASS RUN
67404F
24.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
|
Remove in this Direction | - | - |
67402F
25.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
|
Remove in this Direction | - | - |
69802
26.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
|
Nut |
|
Connector |
69210
27.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
|
Remove in this Direction | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws.
Using a screwdriver with its tip wrapped in protective tape, disconnect the connector.
Disengage the 2 claws and move the lever as shown in the illustration.
Remove the front door outside handle assembly as shown in the illustration.
69510
28.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
|
Remove in this Direction | - | - |
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the TORX screw and remove the front door lock cylinder assembly.
69217D
29.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
|
Remove in this Direction | - | - |
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw to remove the front door outside handle cover.
69241H
30.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD
|
Remove in this Direction | - | - |
69242E
31.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD
|
Remove in this Direction | - | - |
69202A
32.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the snap and remove the front door lock open rod LH as shown in the illustration.
Using a T30 "TORX" socket wrench, loosen the screw.
Detach the wire harness clamps.
Detach the guide and remove the front door outside handle frame sub-assembly.
69312
34.REMOVE FRONT DOOR LOCK OPEN ROD
69710D
36.REMOVE OPEN LEVER FRONT DOOR LOCK REMOTE CONTROL CABLE
69750E
37.REMOVE LOCK / UNLOCK KNOB FRONT DOOR INSIDE LOCKING CABLE
69318C
38.REMOVE DOOR LOCK WIRING HARNESS SEAL
When re-using the front door lock assembly:
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
68610
39.REMOVE FRONT DOOR CHECK ASSEMBLY
|
Nut |
|
Bolt |
67664
40.REMOVE UPPER DOOR FRAME GARNISH
|
Remove in this Direction | - | - |
67862
41.REMOVE FRONT DOOR WEATHERSTRIP
|
Protective Tape | - | - |
Using a clip remover with its tip wrapped in protective tape, detach the clip.
| *a | Protective Tape | - | - |
|
Double-sided Tape | - | - |
Heat the front door weatherstrip using a heat light.
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
| Part | Temperature |
|---|---|
| Front door weatherstrip | 20 to 30°C (68 to 86°F) |
Remove the double-sided tape and using a clip remover, disengage the clip.
Disengage the clip and remove the front door weatherstrip.
75720
42.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY
69802
43.REMOVE FRONT DOOR WINDOW FRAME MOULDING
75754A
44.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING
67496C
45.REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER
67864B
46.REMOVE FRONT DOOR NO. 2 WEATHERSTRIP
|
Protective Tape | - | - |
Using a clip remover with its tip wrapped in protective tape, disengage the claws to remove the front door No. 2 weatherstrip.
67001A
47.REMOVE FRONT DOOR PANEL CUSHION
75986B
48.REMOVE FRONT DOOR NO. 3 STRIPE
75966B
49.REMOVE FRONT DOOR NO. 4 STRIPE
67866F
50.REMOVE FRONT DOOR NO. 3 WEATHERSTRIP
|
Protective Tape | - | - |
Apply protective tape around the front door No. 3 weatherstrip as shown in the illustration.
Heat the front door No. 3 weatherstrip using a heat light.
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
| Part | Temperature |
|---|---|
| Front door No. 3 weatherstrip | 20 to 30°C (68 to 86°F) |
Using a clip remover, remove the clips.
Remove the double-sided tape and front door No. 3 weatherstrip as shown in the illustration.