Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449816 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment  


DESCRIPTION

If the entry luggage compartment door open function does not operate, there may be a malfunction in the luggage electrical key switch circuit or certification ECU (smart key ECU assembly), which receives a signal from the luggage electrical key switch circuit, or a communication error between the vehicle (electrical key antenna (outside luggage compartment)) and electrical key transmitter sub-assembly.

WIRING DIAGRAM

B478136E38
5.958,1.583 6.271,1.781 0.313,0.198 10 false IC 6.063,3.271 6.375,3.469 0.313,0.198 10 false +B 5.417,3.948 5.958,4.188 0.542,0.24 10 false TSW5 5.052,1.052 5.365,1.25 0.313,0.198 10 false G37 5.073,0.844 5.385,1.042 0.313,0.198 10 false 12 5.073,2.135 5.385,2.333 0.313,0.198 10 false 13 5.073,3.854 5.385,4.052 0.313,0.198 10 false 26 5.042,6.271 5.354,6.469 0.313,0.198 10 false D86 5.073,6.073 5.385,6.271 0.313,0.198 10 false 18 1.49,5.896 3.177,6.281 1.688,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 1.51,3.948 1.677,4.146 0.167,0.198 10 false 2 2.906,3.948 3.063,4.125 0.156,0.177 10 false 3 0.229,2.875 3.823,3.177 3.594,0.302 10 false Electrical Key Antenna (Outside Luggage Compartment) 1.667,0.938 2.292,1.24 0.625,0.302 10 false CLGB 2.146,0.938 2.458,1.135 0.313,0.198 10 false 1 2.177,2.219 2.49,2.417 0.313,0.198 10 false 2 5.24,6.917 6.76,7.406 1.521,0.49 10 false Certification ECU (Smart Key ECU Assembly) 0.813,7.281 2.563,7.5 1.75,0.219 10 false : CAN Communication Line 1.625,2.229 2.25,2.531 0.625,0.302 10 false ANTE8 5.406,0.948 5.979,1.208 0.573,0.26 10 false CG8B 5.417,2.229 6.063,2.479 0.646,0.25 10 false CLG8 0.229,2.698 0.542,2.896 0.313,0.198 10 false G51 1.375,4.521 3.365,4.833 1.99,0.313 10 false Luggage Electrical Key Switch 1.375,4.354 1.625,4.552 0.25,0.198 10 false K9 5.438,6.281 5.979,6.521 0.542,0.24 10 false E 5.052,2.333 5.365,2.531 0.313,0.198 10 false G37 5.042,4.063 5.354,4.26 0.313,0.198 10 false G37 1.76,3.958 2.073,4.156 0.313,0.198 10 false E 2.615,3.958 2.927,4.156 0.313,0.198 10 false UL

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.



HINT:
·

If the entry luggage compartment open functions does not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).

·

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.



Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52

PROCEDURE

1.CHECK CUSTOMIZE SETTING (TRUNK OPEN MODE)
Entry & Start
Tester Display Description Default Setting ECU
Trunk Open Mode Function that opens the luggage compartment door when the user is carrying the electrical key transmitter sub-assembly and presses the luggage electrical key switch. ON 0:OFF,1:ON Certification ECU (Smart key ECU assembly)
50006 17
Result:
Result Proceed to
The customize setting is "ON" A
The customize setting is "OFF" B



A

2.CHECK LUGGAGE COMPARTMENT DOOR OPENER SYSTEM

B

2.CHECK LUGGAGE COMPARTMENT DOOR OPENER SYSTEM
a.

Operate the luggage compartment door opening switch assembly in the vehicle and check that the luggage compartment door opens.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE COMPARTMENT DOOR OPENER SYSTEM>OPERATION CHECK


Result:
Result Proceed to
The luggage compartment door opener system opens A
The luggage compartment door opener system does not opens B



A

3.READ VALUE USING GTS (TR/B-DOOR UNLOCK SW)

B

3.READ VALUE USING GTS (TR/B-DOOR UNLOCK SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Luggage electrical key switch OFF or ON OFF: Luggage electrical key switch not pushed
ON: Luggage electrical key switch pushed
·

Displays whether the luggage electrical key switch is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the entry luggage compartment open function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Tr/B-Door Unlock SW
50003 125 17
OK:

The GTS display changes correctly in response to the operation of the luggage electrical key switch.



Result:
Proceed to
OK
NG



OK

4.CHECK WAVE ENVIRONMENT

NG

9.INSPECT LUGGAGE ELECTRICAL KEY SWITCH
4.CHECK WAVE ENVIRONMENT
a.
B581611C01
1.781,1.229 2.01,1.479 0.229,0.25 10 false *a 1.656,1.76 1.885,2.01 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage compartment) and perform an entry luggage compartment open function check.

HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper.

·

When the electrical key transmitter sub-assembly is brought near the electrical key antenna (outside luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Entry functions operate normally.



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

5.CHECK KEY DIAGNOSTIC MODE
5.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

b.
B581611C01
1.781,1.229 2.01,1.479 0.229,0.25 10 false *a 1.656,1.76 1.885,2.01 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1.0 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Buzzer sounds.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G51 electrical key antenna (outside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,G51)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(G51)Body>Floor Wire / No. 3 Floor Wire>Electrical Key Antenna

G37-13 (CLG8) - G51-2 (ANTE8) Always Below 1 Ω
G37-12 (CG8B) - G51-1 (CLGB) Always Below 1 Ω
G37-13 (CLG8) or G51-2 (ANTE8) - Other terminals and body ground Always 10 kΩ or higher
G37-12 (CG8B) or G51-1 (CLGB) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the G37 certification ECU (smart key ECU assembly) connector.


e.

Reconnect the G51 electrical key antenna (outside luggage compartment) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
B473189C27
3.25,0.302 3.615,0.51 0.365,0.208 4.531,0.302 4.896,0.51 0.365,0.208 2.813,2 3.229,1.125 true 3.927,2 3.344,1.125 true 5.594,1.979 5.177,1.208 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 3.313,0.313 3.625,0.51 0.313,0.198 10 false G37 4.594,0.313 4.906,0.51 0.313,0.198 10 false D86 2.51,2.031 3.031,2.24 0.521,0.208 10 false CLG8 3.854,2.031 4.292,2.219 0.438,0.188 10 false CG8B 5.615,1.979 5.875,2.188 0.26,0.208 10 false E 0.865,2.802 1.188,3.01 0.323,0.208 10 false *b 0.729,3.708 1.104,3.917 0.375,0.208 10 false GND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G37,D86)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

G37-13 (CLG8) - D86-18 (E) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Luggage electrical key switch off → on


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
G37-12 (CG8B) - D86-18 (E) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Luggage electrical key switch off → on


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

8.CHECK ENTRY LUGGAGE COMPARTMENT OPEN OPERATION

NG

8.CHECK ENTRY LUGGAGE COMPARTMENT OPEN OPERATION
a.

Connect all connectors and check that the entry luggage compartment open function operates.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Luggage open function operates normally A
Luggage open function does not operate normally B



A

END (CONNECTOR WAS NOT CONNECTED SECURELY)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.INSPECT LUGGAGE ELECTRICAL KEY SWITCH

OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - LUGGAGE ELECTRICAL KEY SWITCH)

NG

REPLACE LUGGAGE ELECTRICAL KEY SWITCH

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - LUGGAGE ELECTRICAL KEY SWITCH)
a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K9 luggage electrical key switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,K9)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(K9)Body>No. 1 Back Door Wire>Luggage Electrical Key Switch

G37-26 (TSW5) - K9-3(UL) Always Below 1 Ω
K9-2(E) - Body ground Always Below 1 Ω
G37-26 (TSW5) or K9-3(UL) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK ENTRY LUGGAGE COMPARTMENT OPEN OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK ENTRY LUGGAGE COMPARTMENT OPEN OPERATION
a.

Connect all connectors and check that the entry luggage compartment open function operates.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Luggage open function operates normally A
Luggage open function does not operate normally B



A

END (CONNECTOR WAS NOT CONNECTED SECURELY)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)