Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Steering Lock does not Lock  


DESCRIPTION

The steering lock ECU (steering lock actuator or upper bracket assembly) activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little, as is done for a vehicle with a mechanical key, to change the position of the lock hole.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Steering Lock does not Lock
Entry&Start
·

Lock Request Receive

·

S Code Check

·

L Code Check

·

Steering Lock


Main Body
·

FL Door Courtesy SW


Power Source Control
·

Shift P Signal



WIRING DIAGRAM

C382197E42
2.281,2.917 2.677,3.094 0.396,0.177 10 false SLR+ 2.354,3.344 2.667,3.531 0.313,0.188 10 false SLP 2.51,3.979 2.667,4.167 0.156,0.188 10 false E 5.365,2.896 5.677,3.083 0.313,0.188 10 false IGE 5.365,3.344 5.771,3.51 0.406,0.167 10 false SLP1 5.365,3.979 5.729,4.167 0.365,0.188 10 false GND 5.375,0.333 5.646,0.51 0.271,0.177 10 false B 2.531,0.313 3.927,0.531 1.396,0.219 10 false from Auxiliary Battery 4.385,0.49 5.49,1 1.104,0.51 10 false STRG LOCK 0.094,2.656 0.438,2.854 0.344,0.198 10 false D73 0.083,2.813 1.677,3.156 1.594,0.344 10 false ID Code Box (Immobiliser Code ECU) 1.635,4.406 1.979,4.604 0.344,0.198 10 false D86 0.688,5.302 2.563,5.594 1.875,0.292 10 false : LIN Communication Line 1.625,4.573 3.74,5 2.115,0.427 10 false Certification ECU (Smart Key ECU Assembly) 4.635,4.51 4.979,4.708 0.344,0.198 10 false D24 4.635,4.667 7.135,5.115 2.5,0.448 10 false Steering Lock Actuator or Upper Bracket Assembly (Steering Lock ECU) 2.75,2.792 2.958,2.969 0.208,0.177 10 false 25 2.75,3.229 2.958,3.406 0.208,0.177 10 false 14 2.74,3.854 2.948,4.031 0.208,0.177 10 false 18 5.146,0.208 5.302,0.375 0.156,0.167 10 false 7 5.146,2.781 5.302,2.948 0.156,0.167 10 false 3 5.156,3.208 5.313,3.375 0.156,0.167 10 false 4 5.156,3.854 5.313,4.021 0.156,0.167 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), refer to the Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Status of steering lock command from certification ECU (smart key ECU assembly) OK or NG OK: Lock request signal received within 10 seconds of any of the doors being opened with shift state park (P) and ignition switch off.
NG: Except above
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Lock Request Receive
50003 125 68
OK:

Within 10 seconds of any of the doors being opened with shift state park (P) and ignition switch off, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (S CODE CHECK)

NG

10.READ VALUE USING GTS (FL DOOR COURTESY SW, FR DOOR COURTESY SW)
2.READ VALUE USING GTS (S CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check S code verification result OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the hybrid control system cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 125 65
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (L CODE CHECK)

NG

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
3.READ VALUE USING GTS (L CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check L code verification result OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the hybrid control system cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator or upper bracket assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - POWER SUPPLY AND BODY GROUND)

NG

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - POWER SUPPLY AND BODY GROUND)
a.

Disconnect the steering lock ECU (steering lock actuator or upper bracket assembly) D24 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D24)Location & Routing

Click Connector(D24)Instrument Panel>Instrument Panel Wire>Steering Lock Actuator or Upper Bracket Assembly

D24-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D24)Location & Routing

Click Connector(D24)Instrument Panel>Instrument Panel Wire>Steering Lock Actuator or Upper Bracket Assembly

D24-7 (B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Reconnect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C389181C44
0.323,2.917 1.656,3.021 1.333,0.104 2.344,2.969 2.75,3.073 0.406,0.104 1.594,4.063 2.417,4.167 0.823,0.104 0.167,0.844 0.573,1.083 0.406,0.24 0.917,3.198 0.917,3.031 false 2,4.063 2,3.896 false 2.573,3.25 2.573,3.073 false 0.688,1.75 1.854,1.083 false 2.302,1.083 2.917,1.75 false 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.844,3.219 1.156,3.375 0.313,0.156 10 false *c 1.938,3.75 2.25,3.906 0.313,0.156 10 false *d 2.5,3.281 2.813,3.479 0.313,0.198 10 false *c 0.573,1.802 1.031,2 0.458,0.198 10 false IGE 2.792,1.802 3.25,2 0.458,0.198 10 false GND 2.969,4.063 3.427,4.26 0.458,0.198 10 false GND 0.25,0.865 0.708,1.063 0.458,0.198 10 false D24 0.146,2.375 0.458,2.531 0.313,0.156 10 false *b
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
*b Waveform
*c Steering Lock Motor not Operating
*d Steering Lock Motor Operating


Using an oscilloscope, check the waveform.

Measurement Condition:
Tester Connection Tool Setting Condition Specified Condition

Click Location & Routing(D24)Location & Routing

Click Connector(D24)Instrument Panel>Instrument Panel Wire>Steering Lock Actuator or Upper Bracket Assembly

D24-3 (IGE) - D24-1 (GND) 2 V/DIV., 200 ms./DIV. Any door opened when conditions below met, and then steering lock motor activated:
·

Shift state park (P)

·

Steering lock unlocked in advance by carrying key and turning ignition switch to ON

·

After above conditions met, ignition switch turned off


Pulse generation
(See waveform)


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the ignition switch to ACC or to ON.

-

To lock the steering, turn the ignition switch off with the shift state park (P), and then open a door.




OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the D24 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D24,D86)Location & Routing

Click Connector(D24)Instrument Panel>Instrument Panel Wire>Steering Lock Actuator or Upper Bracket Assembly

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D24-3 (IGE) - D86-25 (SLR+) Always Below 1 Ω
D24-3 (IGE) or D86-25 (SLR+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Reconnect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C342409C64
1.469,1 1.885,1.25 0.417,0.25 1.917,1.948 2.667,2.667 false 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.563,1.031 1.875,1.188 0.313,0.156 10 false D24 2.615,2.708 2.917,2.885 0.302,0.177 10 false IGE
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D24)Location & Routing

Click Connector(D24)Instrument Panel>Instrument Panel Wire>Steering Lock Actuator or Upper Bracket Assembly

D24-3 (IGE) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY


b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check L code verification result
HINT:

This indicates the certification result of the certification codes of the ID code box (immobiliser code ECU) and EV control ECU.


OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the hybrid control system cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check S code verification result OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the hybrid control system cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 125 65
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

10.READ VALUE USING GTS (FL DOOR COURTESY SW, FR DOOR COURTESY SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Courtesy light switch RH signal OFF or ON OFF: Front door RH closed
ON: Front door RH open
for RHD
FL Door Courtesy SW Courtesy light switch LH signal OFF or ON OFF: Front door LH closed
ON: Front door LH open
for LHD
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

The Data List item changes in accordance with the opening and closing of the driver door.



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

GO TO LIGHTING SYSTEM (DOOR COURTESY SWITCH CIRCUIT)

11.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Change the shift state park (P).


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Pulse P position signal status Normal2, Normal3, Normal4, Normal5 or Unknown Normal2: Signal normal and park (P) selected
Normal3: Signal normal and shift state other than (P)
Normal4: Signal normal and park (N) selected
Normal5: Signal normal and park other than (P) or (N) selected
Unknown: -
Use this item to determine if the P position signal is malfunctioning.
Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal Pulse
50003 223 42
OK:

Normal2 is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (STEERING LOCK)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (PROBLEM SYMPTOMS TABLE)

12.READ VALUE USING GTS (STEERING LOCK)
a.

Check that the steering is unlocked.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock Steering lock ECU (steering lock actuator or upper bracket assembly) lock confirmation status Unset or Set Unset: Lock not confirmed
Set: Lock confirmed
When Unset is displayed, the steering is not locked.
Body Electrical > Entry&Start > Data List
Tester Display
Steering Lock
50003 125 47
OK:

Set is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (LOCK REQUEST RECEIVE)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

13.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



b.

Perform registration.

HINT:

Refer to Service Bulletin.



c.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Status of steering unlock command from certification ECU (smart key ECU assembly) OK or NG OK: Unlock request signal received within 10 seconds of ignition switch being turned to ON or to ACC or of a hybrid control system start operation being performed
NG: Ignition switch not turned to ON or to ACC and hybrid control system start operation not being performed
·

The hybrid control system cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Lock Request Receive
50003 125 68
OK:

Within 10 seconds of any of the doors being opened with shift state park (P) and ignition switch off, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)