Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The certification ECU (smart key ECU assembly) blinks the security indicator light (integration control and panel assembly) when the immobiliser is set (ignition switch off).

·

The certification ECU (smart key ECU assembly) receives the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is in the arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light (radio receiver assembly).


WIRING DIAGRAM

B424449E30
3.25,0.646 3.708,0.844 0.458,0.198 10 false IND 3.615,0.323 4.073,0.521 0.458,0.198 10 false 12 V 2.979,0.646 3.438,0.844 0.458,0.198 10 false 20 1.573,0.656 2.031,0.854 0.458,0.198 10 false 10 1.271,0.74 1.729,0.938 0.458,0.198 10 false LP 3.01,1.417 3.469,1.615 0.458,0.198 10 false D86 3.01,1.583 4.542,1.969 1.531,0.385 10 false Certification ECU (Smart Key ECU Assembly) 0.125,1.406 0.583,1.604 0.458,0.198 10 false D38 0.115,1.563 2.156,1.927 2.042,0.365 10 false Telltale Light Assembly (Security Indicator Light) 0.458,2.458 3.25,2.698 2.792,0.24 10 false : CAN Communication Line 5.375,1.438 7.031,1.844 1.656,0.406 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to the Service Bulletin.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > EV > Trouble Codes
50001 397
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)

NG

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)
a.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Immobiliser Indicator
50004 125 28
OK:

The security indicator light (> Hybrid Control >) operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY) OPERATION

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY))
3.CHECK SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY) OPERATION
a.

When the immobiliser is set, check that the security indicator light (telltale light assembly) blinks.*1

OK:

The security indicator light (telltale light assembly) blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light (telltale light assembly) illuminates.*2

OK:

The security indicator light (telltale light assembly) illuminates normally.



Result:
Result Proceed to
*1 is NG (*2 is OK) A
*2 is NG (*1 is OK) B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY))
a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D38 security indicator light (telltale light assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86,D38)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Click Connector(D38)Instrument Panel>Instrument Panel Wire>Telltale Light Assembly

D86-20 (IND) - D38-10 (LP) Always Below 1 Ω
D86-20 (IND) or D38-10 (LP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the certification ECU (smart key ECU assembly) connector.


b.

Reconnect the D38 security indicator light (telltale light assembly) connector.


c.

Using an oscilloscope, check the waveform.

B427583C96
4.531,0.417 4.948,0.667 0.417,0.25 5.354,2.313 5.021,2.313 5.021,2.313 5.021,1.354 false 0.396,0.177 0.708,0.333 0.313,0.156 10 false *a 4.615,0.448 5.115,0.656 0.5,0.208 10 false D86 5.406,2.25 5.906,2.458 0.5,0.208 10 false IND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Measurement Condition:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-20 (IND) - Body ground Ignition switch off → ON Pulse generation → Below 2 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)