Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

If there is a communication malfunction between the EV control ECU and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the EV control ECU stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either of the following conditions is met (1 trip detection logic*):
·

A malfunction is detected in the communication or communication lines between the EV control ECU and ID code box (immobiliser code ECU).

·

The communication ID codes of the EV control ECU and ID code box (immobiliser code ECU) do not match.


·

ID code box (immobiliser code ECU)

·

EV control ECU

·

Harness or connector


EV A DTC output confirmation operation (Perform either of the following):
·

Start the hybrid control system and wait for 10 seconds. If there is a malfunction, the hybrid control system will stop (communication begins within 3 seconds of the hybrid control system start, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) auxiliary battery terminal, start the hybrid control system and wait for 10 seconds (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B279986 -

WIRING DIAGRAM

B501256E64
5.667,2.948 6.635,3.177 0.969,0.229 10 false D15*1, A8*2 5.677,3.146 6.75,3.479 1.073,0.333 10 false EV Control ECU 6.667,1.604 7.125,1.802 0.458,0.198 10 false 12V 5.448,0.583 5.906,0.781 0.458,0.198 10 false IMO 5.438,1.917 5.896,2.115 0.458,0.198 10 false IMI 5.167,0.563 5.625,0.76 0.458,0.198 10 false 29 5.167,1.896 5.625,2.094 0.458,0.198 10 false 26 1.708,0.552 2.167,0.75 0.458,0.198 10 false EFII 1.635,1.948 2.094,2.146 0.458,0.198 10 false EFIO 2.052,0.563 2.51,0.76 0.458,0.198 10 false 3 2.052,1.917 2.51,2.115 0.458,0.198 10 false 4 0.677,0.125 1.135,0.323 0.458,0.198 10 false 12V 0.344,2.917 0.802,3.115 0.458,0.198 10 false D73 0.333,3.094 2.625,3.5 2.292,0.406 10 false ID Code Box (Immobiliser Code ECU) 3.031,3.125 4,3.354 0.969,0.229 10 false *1: for RHD 4.042,3.135 5.01,3.365 0.969,0.229 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the EV control ECU or ID code box (immobiliser code ECU), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279986 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)
a.

Register the communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

2.CHECK EV CONTROL ECU (TERMINAL IMO)
2.CHECK EV CONTROL ECU (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B599179C05
0.688,0.667 1.073,0.896 0.385,0.229 2.083,0.667 2.469,0.896 0.385,0.229 3.458,0.667 3.844,0.896 0.385,0.229 4.802,0.667 5.188,0.896 0.385,0.229 0.688,0.333 1.073,0.563 0.385,0.229 6.083,0.667 6.469,0.896 0.385,0.229 6.083,0.344 6.469,0.573 0.385,0.229 3.333,4.49 3.115,4.49 3.115,4.49 3.115,3.927 false 2.688,4.49 2.917,4.49 2.917,4.49 2.917,3.927 false 5.917,2.417 6.083,2.417 6.083,2.417 6.24,1.969 true 0.208,0.115 0.458,0.344 0.25,0.229 10 false *a 0.771,0.708 1.146,0.938 0.375,0.229 10 false A14 5.635,2.344 6.01,2.573 0.375,0.229 10 false IMO 0.979,3.906 1.354,4.135 0.375,0.229 10 false GND 2.958,2.969 3.177,3.125 0.219,0.156 10 false *b 3.385,4.427 3.604,4.583 0.219,0.156 10 false *d 2.521,4.427 2.74,4.583 0.219,0.156 10 false *c 2.167,0.708 2.542,0.938 0.375,0.229 10 false A15 3.552,0.708 3.927,0.938 0.375,0.229 10 false A16 4.896,0.708 5.271,0.938 0.375,0.229 10 false A17 6.177,0.708 6.552,0.938 0.375,0.229 10 false D15 6.188,0.385 6.563,0.615 0.375,0.229 10 false A8 0.76,0.365 1.135,0.594 0.375,0.229 10 false G14 1.146,0.344 1.396,0.573 0.25,0.229 10 false *A 1.135,0.698 1.385,0.927 0.25,0.229 10 false *B 6.531,0.365 6.781,0.594 0.25,0.229 10 false *A 6.542,0.677 6.792,0.906 0.25,0.229 10 false *B
*A for LHD *B for RHD
*a Component with harness connected
(EV Control ECU)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

*1: for LHD

*2: for RHD

Click Location & Routing(A8,D15)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A8-29 (IMO) - Body ground*1
D15-29 (IMO) - Body ground*2
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Waveform length or shape is abnormal, or IMO terminal stuck at Hi (12 V) C



A

3.CHECK EV CONTROL ECU (TERMINAL IMI)

B

6.CHECK EV CONTROL ECU (TERMINAL IMO)

C

8.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)
3.CHECK EV CONTROL ECU (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B599180C06
2.083,0.667 2.469,0.885 0.385,0.219 3.458,0.667 3.844,0.885 0.385,0.219 4.823,0.667 5.208,0.885 0.385,0.219 6.063,0.667 6.448,0.885 0.385,0.219 0.708,0.667 1.094,0.885 0.385,0.219 0.708,0.323 1.094,0.542 0.385,0.219 6.063,0.323 6.448,0.542 0.385,0.219 3.729,4.5 3.5,4.5 3.5,4.5 3.5,3.938 false 3.094,4.5 3.313,4.5 3.313,4.5 3.313,3.938 false 6.5,2.417 6.667,2.417 6.667,2.417 6.771,1.958 true 0.26,0.104 0.521,0.302 0.26,0.198 10 false *a 0.792,0.708 1.156,0.906 0.365,0.198 10 false A14 6.271,2.344 6.635,2.542 0.365,0.198 10 false IMI 3.344,2.875 3.656,3.125 0.313,0.25 10 false *b 0.969,3.906 1.385,4.104 0.417,0.198 10 false GND 2.927,4.427 3.24,4.677 0.313,0.25 10 false *c 3.781,4.427 4.094,4.677 0.313,0.25 10 false *d 2.177,0.708 2.542,0.906 0.365,0.198 10 false A15 3.542,0.708 3.906,0.906 0.365,0.198 10 false A16 4.917,0.708 5.281,0.906 0.365,0.198 10 false A17 6.156,0.708 6.521,0.906 0.365,0.198 10 false D15 0.781,0.354 1.146,0.552 0.365,0.198 10 false G14 6.167,0.354 6.531,0.552 0.365,0.198 10 false A8 1.167,0.344 1.427,0.542 0.26,0.198 10 false *A 1.156,0.667 1.417,0.865 0.26,0.198 10 false *B 6.5,0.344 6.76,0.542 0.26,0.198 10 false *A 6.5,0.677 6.76,0.875 0.26,0.198 10 false *B
*A for LHD *B for RHD
*a Component with harness connected
(EV Control ECU)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

*1: for LHD

*2: for RHD

Click Location & Routing(A8,D15)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A8-26 (IMI) - Body ground*1
D15-26 (IMI) - Body ground*2
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

4.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

4.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.


Result:
Result Proceed to
Hybrid control system was started A
Hybrid control system was not started B



A

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

B

6.CHECK EV CONTROL ECU (TERMINAL IMO)

Pre-procedure1

a.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD



Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: for LHD

*2: for RHD

Click Location & Routing(A8,D15)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A8-29 (IMO) - Body ground*1 Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
D15-29 (IMO) - Body ground*2 Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
A8-29 (IMO) - Body ground*1 Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck high (12 V) or abnormal waveform
D15-29 (IMO) - Body ground*2 Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B


Post-procedure1

a.

None.



A

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)

B

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the D73 ID code box (immobiliser code ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: for LHD

*2: for RHD

Click Location & Routing(D73,A8,D15)Location & Routing

Click Connector(D73)Instrument Panel>Instrument Panel Wire>ID Code Box (Immobiliser Code ECU)

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D73-3 (EFII) - A8-29 (IMO)*1 Always Below 1 Ω
D73-3 (EFII) - D15-29 (IMO)*2 Always Below 1 Ω
D73-3 (EFII) or A8-29 (IMO) - Other terminals and body ground*1 Always 10 kΩ or higher
D73-3 (EFII) or D15-29 (IMO) - Other terminals and body ground*2 Always 10 kΩ or higher
D73-4 (EFIO) - A8-26 (IMI)*1 Always Below 1 Ω
D73-4 (EFIO) - D15-26 (IMI)*2 Always Below 1 Ω
D73-4 (EFIO) or A8-26 (IMI) - Other terminals and body ground*1 Always 10 kΩ or higher
D73-4 (EFIO) or D15-26 (IMI) - Other terminals and body ground*2 Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the D73 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: for LHD

*2: for RHD

Click Location & Routing(D73,A8,D15)Location & Routing

Click Connector(D73)Instrument Panel>Instrument Panel Wire>ID Code Box (Immobiliser Code ECU)

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D73-3 (EFII) - A8-29 (IMO)*1 Always Below 1 Ω
D73-3 (EFII) - D15-29 (IMO)*2 Always Below 1 Ω
D73-3 (EFII) or A8-29 (IMO) - Other terminals and body ground*1 Always 10 kΩ or higher
D73-3 (EFII) or D15-29 (IMO) - Other terminals and body ground*2 Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR