Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

If the communication line (IMI - EFIO) between the EV control ECU and ID code box (immobiliser code ECU) is stuck high, the EV control ECU will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B279A12 Engine Immobiliser System Circuit Short to Battery The communication line (IMI - EFIO) between the EV control ECU and ID code box (immobiliser code ECU) is stuck high (1 trip detection logic*).
·

Harness or connector

·

ID code box (immobiliser code ECU)

·

EV control ECU


EV A DTC output confirmation operation:

Turn the ignition switch to ON and wait 6 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started Hybrid control system cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -

WIRING DIAGRAM

B499509E42
0.479,1.885 3.115,2.25 2.635,0.365 10 false ID Code Box (Immobiliser Code ECU) 0.49,1.729 0.958,1.969 0.469,0.24 10 false D73 1.781,0.729 2.25,0.969 0.469,0.24 10 false EFIO 2.177,0.729 2.646,0.969 0.469,0.24 10 false 4 5.427,1.927 7.146,2.292 1.719,0.365 10 false EV Control ECU 5.427,1.74 6.656,2.083 1.229,0.344 10 false A8*1, D15*2 5.125,0.75 5.594,0.99 0.469,0.24 10 false IMI 4.875,0.719 5.344,0.958 0.469,0.24 10 false 26 6.354,0.385 6.823,0.625 0.469,0.24 10 false 12V 3.24,2 4.469,2.344 1.229,0.344 10 false *1: for LHD 3.229,2.292 4.458,2.635 1.229,0.344 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

When replacing the EV control ECU or ID code box (immobiliser code ECU), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279A12 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK CONNECTION OF CONNECTOR

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Check that the connectors are properly connected to the EV control ECU and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.



Result:
Result Proceed to
The connectors are properly connected A
The connectors are not properly connected B


Post-procedure1

a.

None.



A

2.CHECK EV CONTROL ECU (TERMINAL IMI)

B

CONNECT CONNECTORS PROPERLY

2.CHECK EV CONTROL ECU (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B599180C07
2.083,0.667 2.469,0.885 0.385,0.219 3.458,0.667 3.844,0.885 0.385,0.219 4.823,0.667 5.208,0.885 0.385,0.219 6.063,0.667 6.448,0.885 0.385,0.219 0.708,0.667 1.094,0.885 0.385,0.219 0.708,0.333 1.094,0.552 0.385,0.219 6.063,0.344 6.448,0.563 0.385,0.219 3.729,4.5 3.5,4.5 3.5,4.5 3.5,3.938 false 3.094,4.5 3.313,4.5 3.313,4.5 3.313,3.938 false 6.5,2.417 6.667,2.417 6.667,2.417 6.771,1.958 true 0.26,0.104 0.521,0.302 0.26,0.198 10 false *a 0.792,0.708 1.156,0.906 0.365,0.198 10 false A14 6.271,2.344 6.635,2.542 0.365,0.198 10 false IMI 3.344,2.875 3.656,3.125 0.313,0.25 10 false *b 0.969,3.906 1.385,4.104 0.417,0.198 10 false GND 2.927,4.427 3.24,4.677 0.313,0.25 10 false *c 3.781,4.427 4.094,4.677 0.313,0.25 10 false *d 2.177,0.708 2.542,0.906 0.365,0.198 10 false A15 3.542,0.708 3.906,0.906 0.365,0.198 10 false A16 4.917,0.708 5.281,0.906 0.365,0.198 10 false A17 6.177,0.375 6.542,0.573 0.365,0.198 10 false A8 0.781,0.365 1.146,0.563 0.365,0.198 10 false G14 1.177,0.354 1.438,0.552 0.26,0.198 10 false *A 1.177,0.677 1.438,0.875 0.26,0.198 10 false *B 6.531,0.365 6.792,0.563 0.26,0.198 10 false *A 6.531,0.688 6.792,0.885 0.26,0.198 10 false *B 6.146,0.698 6.51,0.896 0.365,0.198 10 false D15
*A for LHD *B for RHD
*a Component with harness connected
(EV Control ECU)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

*1: for LHD

*2: for RHD

Click Location & Routing(A8,D15)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A8-26 (IMI) - Body ground*1
D15-26 (IMI) - Body ground*2
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal waveform



A

3.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)

B

3.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD



b.

Disconnect the D73 ID code box (immobiliser code ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: for LHD

*2: for RHD

Click Location & Routing(D73,A8,D15)Location & Routing

Click Connector(D73)Instrument Panel>Instrument Panel Wire>ID Code Box (Immobiliser Code ECU)

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D73-4 (EFIO) - A8-26 (IMI)*1
D73-4 (EFIO) - D15-26 (IMI)*2
Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR