Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser function compares the ID code that is registered to the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

WIRING DIAGRAM

B501256E64
5.667,2.948 6.635,3.177 0.969,0.229 10 false D15*1, A8*2 5.677,3.146 6.75,3.479 1.073,0.333 10 false EV Control ECU 6.667,1.604 7.125,1.802 0.458,0.198 10 false 12V 5.448,0.583 5.906,0.781 0.458,0.198 10 false IMO 5.438,1.917 5.896,2.115 0.458,0.198 10 false IMI 5.167,0.563 5.625,0.76 0.458,0.198 10 false 29 5.167,1.896 5.625,2.094 0.458,0.198 10 false 26 1.708,0.552 2.167,0.75 0.458,0.198 10 false EFII 1.635,1.948 2.094,2.146 0.458,0.198 10 false EFIO 2.052,0.563 2.51,0.76 0.458,0.198 10 false 3 2.052,1.917 2.51,2.115 0.458,0.198 10 false 4 0.677,0.125 1.135,0.323 0.458,0.198 10 false 12V 0.344,2.917 0.802,3.115 0.458,0.198 10 false D73 0.333,3.094 2.625,3.5 2.292,0.406 10 false ID Code Box (Immobiliser Code ECU) 3.031,3.125 4,3.354 0.969,0.229 10 false *1: for RHD 4.042,3.135 5.01,3.365 0.969,0.229 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ID code box (immobiliser code ECU) or EV control ECU, refer to the Service Bulletin.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > EV > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS

B

2.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts within 5 seconds of the ignition switch being turned to ON (READY).

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK EV CONTROL ECU (TERMINAL IMI AND IMO)
3.CHECK EV CONTROL ECU (TERMINAL IMI AND IMO)
a.

Using an oscilloscope, check the waveform.

B599181C04
1.042,0.583 1.417,0.813 0.375,0.229 2.25,0.583 2.625,0.813 0.375,0.229 3.479,0.583 3.854,0.813 0.375,0.229 4.677,0.583 5.052,0.813 0.375,0.229 5.781,0.583 6.156,0.813 0.375,0.229 1.042,0.26 1.417,0.49 0.375,0.229 5.781,0.25 6.156,0.479 0.375,0.229 3.406,4.198 3.177,4.198 3.177,4.198 3.177,3.646 false 2.771,4.198 2.99,4.198 2.99,4.198 2.99,3.646 false 3.823,6.135 3.594,6.135 3.594,6.135 3.594,5.688 false 3.625,6.302 3.396,6.302 3.396,6.302 3.396,5.698 false 5.583,2.167 5.75,2.167 5.75,2.167 5.938,1.729 true 6.667,2.167 6.5,2.167 6.5,2.167 6.417,1.729 true 0.625,0.24 0.906,0.448 0.281,0.208 10 false *a 2.594,4.135 2.906,4.292 0.313,0.156 10 false *b 3.469,4.125 3.781,4.281 0.313,0.156 10 false *c 1.854,7.125 2.167,7.281 0.313,0.156 10 false *d 1.938,7.365 2.25,7.521 0.313,0.156 10 false *e 1.313,2.479 1.625,2.635 0.313,0.156 10 false *f 1.302,4.51 1.615,4.667 0.313,0.156 10 false *g 2.458,4.635 2.771,4.792 0.313,0.156 10 false *h 3.042,2.677 3.354,2.833 0.313,0.156 10 false *i 3.469,4.635 3.781,4.792 0.313,0.156 10 false *j 1.448,6.5 1.76,6.656 0.313,0.156 10 false *k 1.115,0.625 1.552,0.875 0.438,0.25 10 false A14 5.302,2.094 5.74,2.344 0.438,0.25 10 false IMO 6.76,2.094 7.146,2.344 0.385,0.25 10 false IMI 1.052,3.625 1.563,3.917 0.51,0.292 10 false GND 1.052,5.656 1.563,5.948 0.51,0.292 10 false GND 3.865,6.073 4.177,6.229 0.313,0.156 10 false *c 3.667,6.24 3.979,6.396 0.313,0.156 10 false *b 3.177,6.5 3.49,6.656 0.313,0.156 10 false *k 3.74,7.125 4.052,7.281 0.313,0.156 10 false *d 3.677,7.365 3.99,7.521 0.313,0.156 10 false *e 2.333,0.625 2.771,0.875 0.438,0.25 10 false A15 3.563,0.625 4,0.875 0.438,0.25 10 false A16 4.76,0.625 5.198,0.875 0.438,0.25 10 false A17 5.865,0.625 6.302,0.875 0.438,0.25 10 false D15 1.104,0.313 1.542,0.563 0.438,0.25 10 false G14 5.885,0.281 6.323,0.531 0.438,0.25 10 false A8 1.469,0.281 1.75,0.49 0.281,0.208 10 false *A 1.469,0.583 1.75,0.792 0.281,0.208 10 false *B 6.219,0.271 6.5,0.479 0.281,0.208 10 false *A 6.219,0.604 6.5,0.813 0.281,0.208 10 false *B
*A for LHD *B for RHD
*a Component with harness connected
(EV Control ECU()
*b Approximately 160 ms.
*c Approximately 270 ms. *d Approximately 40 ms.
*e Approximately 60 ms. *f IMO Waveform
*g IMI Waveform *h Waveform A
*i Waveform B *j Waveform C
*k Waveform A (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

*1: for LHD

*2: for RHD

Click Location & Routing(A8,D15)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A8-29 (IMO) - Body ground*1
D15-29 (IMO) - Body ground*2
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 2)
A8-26 (IMI) - Body ground*1
D15-26 (IMI) - Body ground*2
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1 and 3)



Result:
Result Proceed to
Normal waveform A
Waveform A is not output, or has abnormal wavelength or shape B
Waveform B is not output, or has abnormal wavelength or shape C
Waveform C is not output, or has abnormal wavelength or shape D



A

4.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)

B

6.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)

C

D

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
4.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID WAS NOT REGISTERED)

NG

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
6.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - EV CONTROL ECU)
a.

Disconnect the D73 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: for LHD

*2: for RHD

Click Location & Routing(D73,A8,D15)Location & Routing

Click Connector(D73)Instrument Panel>Instrument Panel Wire>ID Code Box (Immobiliser Code ECU)

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D73-3 (EFII) - A8-29 (IMO)*1
D73-3 (EFII) - D15-29 (IMO)*2
Always Below 1 Ω
D73-4 (EFIO) - A8-26 (IMI)*1
D73-4 (EFIO) - D15-26 (IMI)*2
Always Below 1 Ω
D73-3 (EFII) or A8-29 (IMO) - Other terminals and body ground*1
D73-3 (EFII) or D15-29 (IMO) - Other terminals and body ground*2
Always 10 kΩ or higher
D73-4 (EFIO) or A8-26 (IMI) - Other terminals and body ground*1
D73-4 (EFIO) or D15-26 (IMI) - Other terminals and body ground*2
Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.REGISTER RECOGNITION CODE
8.REGISTER RECOGNITION CODE
a.

Register the recognition codes to the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
10.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG