Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2275  STSW Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction is detected in the starter circuit inside the certification ECU (smart key ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B2275 STSW Monitor Malfunction Certification ECU (smart key ECU assembly) internal hybrid activation request output circuit malfunction or external circuit malfunction (1-trip detection logic*)
·

Certification ECU (smart key ECU assembly)

·

EV control ECU

·

Harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 10 seconds or more, then start the hybrid control system 3 times.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

The power source mode changes to on (READY) even though the hybrid control system is not started.

·

The power source mode does not change to on (READY) even though the hybrid control system is started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2275
Power Source Control
·

Starter Request Signal



WIRING DIAGRAM

C375424E35
5.729,0.698 6.104,0.927 0.375,0.229 10 false +B 6.208,1.323 6.583,1.552 0.375,0.229 10 false IC 5.271,1.083 5.646,1.313 0.375,0.229 10 false ST2 5.042,1.073 5.417,1.302 0.375,0.229 10 false 27 1.281,1.094 1.656,1.323 0.375,0.229 10 false ST2 1.625,1.052 2,1.281 0.375,0.229 10 false 19 0.688,2.708 1.063,2.938 0.375,0.229 10 false D15 0.688,2.885 1.813,3.188 1.125,0.302 10 false EV control ECU 4.969,2.698 5.344,2.927 0.375,0.229 10 false D86 4.969,2.865 7.073,3.479 2.104,0.615 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait 25 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
OK:

DTC B2285 is not output simultaneously.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EV CONTROL ECU)

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D15 EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86,D15)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D86-27 (ST2) - D15-19 (ST2) Always Below 1 Ω
D86-27 (ST2) or D15-19 (ST2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.
B498244C66
1.604,0.115 1.969,0.354 0.365,0.24 1.021,1.979 1.219,1.979 1.219,1.979 1.219,1.083 true 1.667,0.135 2.01,0.333 0.344,0.198 10 false D86 0.719,1.885 1.313,2.083 0.594,0.198 10 false ST2 0.115,0.073 0.708,0.271 0.594,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the certification ECU (smart key ECU assembly) connector.


b.

Reconnect the D15 EV control ECU connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specification Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-27 (ST2) - Body ground With the brake pedal depressed, the power switch is pressed and held 8.5 V or higher
D86-27 (ST2) - Body ground After approximately 3 sec. has elapsed, the power switch is released 1 V or less



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)