Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM37H0E _55 Steering _095771 STEERING GEAR / LINKAGE _0449974 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C449414N02
2.542,0.823 2.667,0.417 2.667,0.417 2.833,0.417 true 2.875,1.031 3,0.667 3,0.667 3.167,0.667 true 3.375,1.25 3.5,1 3.5,1 3.667,1 true 5.688,5.521 6.021,5.521 true 3.927,1.667 4.083,1.5 4.083,1.5 4.25,1.5 true 4.531,3.677 4.792,3.083 4.792,3.083 4.958,3.083 true 3.573,5.323 3.688,5.323 3.688,5.323 3.958,4.823 true 3.177,5 3.344,5 3.344,5 3.417,4.573 true 4.365,5.323 4.448,5.323 4.448,5.323 4.521,5.021 true 4.583,5.583 4.667,5.583 4.667,5.583 4.802,5.177 true 1.5,0.406 1.833,0.406 true 2.865,4.896 3.146,5.25 0.281,0.354 10 false ● 3.927,0.833 4.208,1.188 0.281,0.354 18 false 2 4.479,1.333 4.927,1.646 0.448,0.313 18 false 4 5.302,2.927 5.656,3.229 0.354,0.302 18 false 7 4.313,1.396 4.583,1.667 0.271,0.271 10 false ● 3.385,5.208 3.646,5.49 0.26,0.281 18 false 1 3.01,4.833 3.365,5.115 0.354,0.281 18 false 3 2.896,0.333 3.177,0.688 0.281,0.354 10 false *1 4.198,5.198 4.49,5.49 0.292,0.292 18 false 5 3.24,0.51 3.521,0.865 0.281,0.354 18 false 6 4.427,5.5 4.667,5.75 0.24,0.25 10 false *1 6.354,5.385 6.708,5.667 0.354,0.281 18 false 8 1.292,0.271 1.604,0.563 0.313,0.292 18 false 9 0.083,0.083 0.365,0.438 0.281,0.354 10 false *A 3.719,0.896 3.958,1.146 0.24,0.25 10 false ● 3.219,5.229 3.417,5.479 0.198,0.25 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 2 STEERING RACK BOOT 45536 (Click here) - -
2 NO. 1 STEERING RACK BOOT 45535 - - -
3 NO. 2 STEERING RACK BOOT CLAMP (for LH Side) 45538 (Click here) - -
4 NO. 2 STEERING RACK BOOT CLAMP (for RH Side) 45538 - - -
5 STEERING RACK BOOT CLIP (for LH Side) 45535B (Click here) - -
6 STEERING RACK BOOT CLIP (for RH Side) 45535B - - -
7 INSPECT RACK AND PINION POWER STEERING GEAR ASSEMBLY - (Click here) - -
8 TIE ROD ASSEMBLY LH 45470 (Click here) - -
9 TIE ROD ASSEMBLY RH 45460 - - -

*A for LHD - -
*1 LOCK NUT - -
● Non-reusable part
V100135

Lithium soap base glycol grease

C440510N02
0.667,3.083 1.5,3.25 0.833,0.167 4.083,3.365 4.25,2.917 4.25,2.917 4.417,2.917 true 1.583,4 1.75,4 1.75,4 2.083,3.333 true 5.917,5.521 5.677,5.521 true 1.833,0.417 1.583,0.417 true 4.708,4.917 4.625,4.917 4.625,4.917 4.552,5 true 3.083,0.583 2.917,0.583 2.917,0.583 2.854,1.021 true 3.188,4.938 3.354,4.938 3.354,4.938 3.427,4.573 true 3.563,0.865 3.396,0.865 3.396,0.865 3.313,1.229 true 4.083,1.333 3.917,1.333 3.917,1.333 3.833,1.552 true 3.771,5.344 3.938,5.344 3.938,5.344 4.104,4.865 true 1.75,3.167 1.5,3.167 true 4.583,5.417 4.667,5.417 4.667,5.417 4.792,5.167 true 2.833,0.333 2.667,0.333 2.667,0.333 2.542,0.823 true 4.865,2.75 5.146,3.104 0.281,0.354 18 false 7 1.271,3.865 1.583,4.219 0.313,0.354 18 false 10 6.375,5.417 6.656,5.771 0.281,0.354 18 false 8 1.365,0.271 1.646,0.625 0.281,0.354 18 false 9 5.01,4.792 5.292,5.146 0.281,0.354 18 false 5 3.167,0.448 3.448,0.802 0.281,0.354 18 false 6 2.979,4.813 3.26,5.167 0.281,0.354 18 false 3 3.771,0.708 4.052,1.063 0.281,0.354 18 false 2 4.323,1.188 4.667,1.583 0.344,0.396 18 false 4 3.615,5.208 3.854,5.552 0.24,0.344 18 false 1 2.833,4.854 3.167,5.219 0.333,0.365 10 false ● 4.156,1.271 4.365,1.469 0.208,0.198 10 false ● 0.729,3.094 1.896,3.26 1.167,0.167 8 false 12.5 (127, 9) 0.083,0.083 0.333,0.333 0.25,0.25 10 false *A 4.385,5.344 4.667,5.698 0.281,0.354 10 false *1 2.896,0.271 3.177,0.625 0.281,0.354 10 false *1 3.635,0.75 3.844,0.948 0.208,0.198 10 false ● 3.479,5.229 3.698,5.49 0.219,0.26 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 2 STEERING RACK BOOT 45536 (Click here) - -
2 NO. 1 STEERING RACK BOOT 45535 - - -
3 NO. 2 STEERING RACK BOOT CLAMP (for LH Side) 45538 (Click here) - -
4 NO. 2 STEERING RACK BOOT CLAMP (for RH Side) 45538 - - -
5 STEERING RACK BOOT CLIP (for LH Side) 45535B (Click here) - -
6 STEERING RACK BOOT CLIP (for RH Side) 45535B - - -
7 INSPECT RACK AND PINION POWER STEERING GEAR ASSEMBLY - (Click here) - -
8 TIE ROD ASSEMBLY LH 45470 (Click here) - -
9 TIE ROD ASSEMBLY RH 45460 - - -
10 WIRE HARNESS CLAMP BRACKET (for RHD) - - - -

*A for RHD - -
*1 LOCK NUT - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Lithium soap base glycol grease - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45536 1.INSTALL NO. 2 STEERING RACK BOOT

a.
C447766C01
3.927,0.031 4.292,0.365 0.365,0.333 18 false ii 0.531,0.021 0.896,0.354 0.365,0.333 18 false i
V100135

Lithium Soap Base Glycol Grease - -


i.

Apply lithium soap base glycol grease to the inside of the small opening of the a new No. 2 steering rack boot.


ii.

Install the No. 2 steering rack boot to the groove of the rack housing.

NOTICE:
·

Be careful not to damage or twist the No. 2 steering rack boot.

·

Make sure that the No. 2 steering rack boot is free of rust and foreign matter.

·

Make sure that the boot is free of water, rust, foreign matter, etc.

·

Do not touch the inside of the rack boot or rack bar when performing installation.





Hide 45535 2.INSTALL NO. 1 STEERING RACK BOOT

a.

Perform the same procedure as for the No. 2 steering rack boot.


Hide 45536A 3.INSTALL NO. 2 STEERING RACK BOOT CLAMP (for LH Side)

a.
C447767N01
0.51,0.021 0.813,0.323 0.302,0.302 18 false i 4.375,0.042 4.917,0.375 0.542,0.333 18 false ii, iii

i.

Temporarily install a new No. 2 steering rack boot clamp to the No. 2 steering rack boot.

NOTICE:

Do not damage the No. 2 steering rack boot.


HINT:
C447739C03
0,0 0,0 false
V100135

Top of Vehicle
V100136

Rear of Vehicle


Make sure that the protrusion of the No. 2 steering rack boot clamp is positioned within the area shown in the illustration.



ii.

Using SST, install the No. 2 steering rack boot clamp as shown in the illustration.

SST
09521-24010  

NOTICE:
·

Do not pinch the No. 2 steering rack boot clamp excessively.

·

Be careful not to damage or twist the No. 2 steering rack boot.




iii.

Remove SST and measure the clearance of the No. 2 steering rack boot clamp.

Clearance:

2.5 to 4.0 mm (0.0984 to 0.157 in.)




Hide 45536A 4.INSTALL NO. 2 STEERING RACK BOOT CLAMP (for RH Side)

a.

Perform the same procedure as for the LH side.


Hide 45535B 5.INSTALL STEERING RACK BOOT CLIP (for LH Side)

a.
C449477N01
0.542,0.156 0.823,0.51 0.281,0.354 18 false i

i.

Using pliers, install the steering rack boot clip.

HINT:
C447783C01
0.927,0.865 1.24,1.021 0.313,0.156 10 false *a 1.083,0.698 1.396,0.854 0.313,0.156 10 false *b 1.875,0.594 2.188,0.75 0.313,0.156 10 false *c 2.375,0.917 2.688,1.073 0.313,0.156 10 false *d
*a Clip Tab Positioning Area
*b 90°
*c 45°
*d 58°
V100135

Top of Vehicle
V100136

Rear of Vehicle


Make sure that the tabs of the clip are facing the rear of the vehicle.




Hide 45535B 6.INSTALL STEERING RACK BOOT CLIP (for RH Side)

a.

Perform the same procedure as for the LH side.


Hide 44250 7.INSPECT RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.
C447768N01
4.271,0.677 4.5,0.833 4.5,0.833 4.75,0.833 false 4.813,0.729 5.271,0.927 0.458,0.198 10 false SST 0.49,0.021 0.833,0.323 0.344,0.302 18 false i

i.

Using SST, turn the pinion shaft and check that the left and the right steering rack boots expand and contract smoothly.

SST
09616-00011  

HINT:

If the operation cannot be performed as specified, use new steering rack boot clamps and reinstall the steering rack boots.




Hide 45470 8.INSTALL TIE ROD ASSEMBLY LH

a.
C440528C01
2.99,0.938 3.24,0.604 3.24,0.604 2.865,0.938 true 0.531,0.052 0.813,0.406 0.281,0.354 18 false i 3.26,0.49 3.573,0.688 0.313,0.198 10 false *a
*a Matchmark - -


i.

Install the lock nut and tie rod assembly LH to the steering rack end sub-assembly until the matchmarks are aligned.

HINT:

After adjusting toe-in, tighten the lock nut.




Hide 45460 9.INSTALL TIE ROD ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 10.INSTALL WIRE HARNESS CLAMP BRACKET (for RHD)

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)