Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM37H0E _58 Vehicle Interior _095313 DOOR LOCK _0452395 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly) via CAN communication system. The certification ECU (smart key ECU assembly) sends door lock/unlock commands to the main body ECU (multiplex network body ECU).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1242 Wireless Door Lock Tuner Circuit Malfunction One of the following conditions is met:
·

Short in RDAM between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short in RCO between the certification ECU (smart key ECU assembly) and door control receiver.


·

Door control receiver

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Entry&Start A

WIRING DIAGRAM

E329246E30
4.938,0.927 5.396,1.125 0.458,0.198 10 false G37 4.938,2.219 5.396,2.417 0.458,0.198 10 false D86 5.781,0.427 6.24,0.625 0.458,0.198 10 false 5 V 5.833,1.125 6.292,1.323 0.458,0.198 10 false +B 5.271,0.833 5.729,1.031 0.458,0.198 10 false RCO 5.271,1.531 5.729,1.729 0.458,0.198 10 false RDAM 5.281,2.219 5.74,2.417 0.458,0.198 10 false E 5.344,2.844 6.76,3.438 1.417,0.594 10 false Certification ECU (Smart Key ECU Assembly) 2.156,2.115 2.615,2.313 0.458,0.198 10 false 12 2.156,1.51 2.615,1.708 0.458,0.198 10 false 2 2.156,0.833 2.615,1.031 0.458,0.198 10 false 8 1.906,0.833 2.365,1.031 0.458,0.198 10 false +5 1.698,1.521 2.156,1.719 0.458,0.198 10 false DATA 1.781,2.219 2.24,2.417 0.458,0.198 10 false GND 0.865,1.427 1.323,1.625 0.458,0.198 10 false IC 0.667,2.677 1.75,2.917 1.083,0.24 10 false G157*1, G49*2 0.677,2.854 2.083,3.427 1.406,0.573 10 false Door Control Receiver 4.979,0.771 5.208,0.927 0.229,0.156 10 false 18 4.979,2.063 5.208,2.219 0.229,0.156 10 false 18 4.99,1.448 5.219,1.604 0.229,0.156 10 false 19 4.938,1.625 5.396,1.823 0.458,0.198 10 false G37 0.229,3.229 2.177,3.469 1.948,0.24 10 false *1: w/ Panic Switch 0.229,3.49 2.177,3.729 1.948,0.24 10 false *2: w/o Panic Switch

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the certification ECU (smart key ECU assembly) is replaced, refer to the Service Bulletin.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and start function and wireless control function performance may be affected.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

This DTC is not stored within 10 seconds of the ignition switch being turned from on (IG) to off.

·

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced.




PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the G157*1 or G49*2 door control receiver connector.

*1: w/ Panic Switch

*2: w/o Panic Switch


B440788C44
3.198,0.448 3.604,0.688 0.406,0.24 4.521,0.427 4.927,0.667 0.406,0.24 4.115,2.583 3.979,2.583 3.979,2.583 3.813,1.448 false 4.896,2.594 4.76,2.594 4.76,2.594 3.906,1.438 false 5.688,2.25 5.552,2.25 5.552,2.25 5.208,1.448 false 3.302,0.49 3.76,0.688 0.458,0.198 10 false G37 4.615,0.469 5.073,0.667 0.458,0.198 10 false D86 4.958,2.51 5.573,2.708 0.615,0.198 10 false RCO 4.177,2.51 4.792,2.708 0.615,0.198 10 false RDAM 5.75,2.177 6.365,2.375 0.615,0.198 10 false E 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



Procedure1

a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-19 (RDAM) - D86-18 (E) Always 11 to 14 V
D86-18 (RCO) - D86-18 (E) Always Pulse generation at regular intervals
(Below 1 V ←→ 4.5 to 5.5 V)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-18 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE DOOR CONTROL RECEIVER

NG

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

Pre-procedure1

a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G157*1 or G49*2 door control receiver connector.

*1: w/ Panic Switch

*2: w/o Panic Switch



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G37,G157)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(G157)Body>Floor Wire / No. 3 Floor Wire>Door Control Receiver

G37-19 (RDAM) - G157-2 (DATA) Always Below 1 Ω
G37-18 (RCO) - G157-8 (+5) Always Below 1 Ω
G157-12 (GND) - Body ground Always Below 1 Ω
G157-2 (DATA) or G37-19 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
G157-8 (+5) or G37-18 (RCO) - Other terminals and body ground Always 10 kΩ or higher

w/o Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G37,G49)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G37-19 (RDAM) - G49-2 (DATA) Always Below 1 Ω
G37-18 (RCO) - G49-8 (+5) Always Below 1 Ω
G49-12 (GND) - Body ground Always Below 1 Ω
G49-2 (DATA) or G37-19 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
G49-8 (+5) or G37-18 (RCO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR