Use the following procedure to troubleshoot the power window control system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read out and saved, the operation history information could be lost.
The function "Read operation history" uses the current system time setting inside the GTS and the time counter inside the controlling ECU to calculate the timings shown in the operation history. For this reason, before reading out the operation history, first make sure that the GTS system clock is accurately set to the current time.
Read and save operation history using the GTS.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
| Tester Display |
|---|
| Operation History |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage with the ignition switch off.
11 to 14 V
A simple method to determine whether the auxiliary battery is discharged is to operate the horn.
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, check for CAN communication system DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, check for LIN communication system DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| LIN DTCs are not output | A |
| LIN DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs and make a note of any codes that are output.
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Refer to Problem Symptoms Table.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table (Fault can be simulated) | A |
| Fault is not listed in Problem Symptoms Table (Fault cannot be simulated) | B |
| Fault is listed in Problem Symptoms Table | C |
A
B
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
C
Operation Check
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK
Terminals of ECU
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>TERMINALS OF ECU
Data List / Active Test
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST
Fail-safe Chart
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>FAIL-SAFE CHART
Inspection
| Proceed to |
|---|
| NEXT |
NEXT
Check if any of the door window regulators, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled.
| Result | Proceed to |
|---|---|
| Any of the door window regulators, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled. | A |
| The door window regulators, power window regulator motor assemblies, door glass or door glass runs have not been removed and reinstalled. | B |
A
B
Initialize the power window control system.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT