Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM37H0E _59 Vehicle Exterior _095305 WINDOW / GLASS _0453652 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


a.
B187998C19
0.958,0.208 1.375,0.469 0.417,0.26 1.927,0.208 2.344,0.469 0.417,0.26 2.01,0.25 2.302,0.438 0.292,0.188 10 false E14 1.458,0.25 1.771,0.448 0.313,0.198 10 false *A 1.042,0.26 1.333,0.417 0.292,0.156 10 false E32 2.427,0.25 2.74,0.448 0.313,0.198 10 false *B
*A for LHD
*B for RHD


Disconnect the E32*1 or E14*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
E32-11 (B) - E32-12 (GND) Auxiliary battery power supply Ignition switch off 11 to 14 V
E32-12 (GND) - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
E14-11 (B) - E14-12 (GND) Auxiliary battery power supply Ignition switch off 11 to 14 V
E14-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the E32*1 or E14*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
E32-15 (DOWN) - E32-12 (GND) Power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
E32-20 (UP) - E32-12 (GND) Power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
E14-15 (DOWN) - E14-12 (GND) Power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
E14-20 (UP) - E14-12 (GND) Power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V


e.

Measure the pulse according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/ Reverse Shift-linked Mirror

E32-16 (LIN2) - Body ground* LIN communication line Ignition switch ON Pulse generation
E32-17 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/ Reverse Shift-linked Mirror

E14-16 (LIN2) - Body ground* LIN communication line Ignition switch ON Pulse generation
E14-17 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for LHD)


a.
B527906E16
1.5,0.156 1.938,0.438 0.438,0.281 1.594,0.208 2.052,0.406 0.458,0.198 10 false E20

Disconnect the E20 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
E20-1 (GND) - Body ground Ground Always Below 1 Ω
E20-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the E20 front power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E20-7 (DOWN) - E20-1 (GND) Power window motor DOWN input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
E20-10 (UP) - E20-1 (GND) Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully opened 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/ Reverse Shift-linked Mirror

E20-9 (LIN) - Body ground* LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for RHD)


a.
B527906E16
1.5,0.156 1.938,0.438 0.438,0.281 1.594,0.208 2.052,0.406 0.458,0.198 10 false E20

Disconnect the E20 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
E20-1 (GND) - Body ground Ground Always Below 1 Ω
E20-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the E20 front power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E20-7 (DOWN) - E20-1 (GND) Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
E20-4 (AUTO) - E20-1 (GND) Power window motor AUTO UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
E20-10 (UP) - E20-1 (GND) Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E20-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for LHD)


a.
B527906E17
1.5,0.156 1.938,0.438 0.438,0.281 1.635,0.219 2.094,0.417 0.458,0.198 10 false E2

Disconnect the E2 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
E2-1 (GND) - Body ground Ground Always Below 1 Ω
E2-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the E2 front power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E2-4 (AUTO) - E2-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
E2-7 (DOWN) - E2-1 (GND) Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
E2-10 (UP) - E2-1 (GND) Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E2-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for RHD)


a.
B527906E17
1.5,0.156 1.938,0.438 0.438,0.281 1.635,0.219 2.094,0.417 0.458,0.198 10 false E2

Disconnect the E2 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
E2-1 (GND) - Body ground Ground Always Below 1 Ω
E2-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the E2 front power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E2-7 (DOWN) - E2-1 (GND) Power window motor DOWN input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
E2-10 (UP) - E2-1 (GND) Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E2-9 (LIN) - Body ground LIN communication line Ignition switch off Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


a.
B527906E18
1.5,0.156 1.938,0.438 0.438,0.281 1.604,0.219 2.063,0.417 0.458,0.198 10 false F12

Disconnect the F12 rear power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
F12-1 (GND) - Body ground Ground Always Below 1 Ω
F12-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the F12 rear power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
F12-4 (AUTO) - F12-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear LH door power window fully open 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
F12-7 (DOWN) - F12-1 (GND) Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly LH not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
F12-10 (UP) - F12-1 (GND) Power window motor UP input Ignition switch ON, rear power window regulator switch assembly LH not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F12-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


a.
B527906E19
1.5,0.156 1.938,0.438 0.438,0.281 1.635,0.219 2.094,0.417 0.458,0.198 10 false F1

Disconnect the F1 rear power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
F1-1 (GND) - Body ground Ground Always Below 1 Ω
F1-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the F1 rear power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F1-4 (AUTO) - F1-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear RH door power window fully open 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
F1-7 (DOWN) - F1-1 (GND) Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly RH not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
F1-10 (UP) - F1-1 (GND) Power window motor UP input Ignition switch ON, rear power window regulator switch assembly RH not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F1-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH (w/ Reverse Shift-linked Mirror, Double Locking System)


B338775E25
3.354,0.219 3.802,0.458 0.448,0.24 3.458,0.25 3.917,0.448 0.458,0.198 10 false E25

a.

Disconnect the E25 front multiplex network door ECU LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E25-6 (BDR) - E25-1 (GND) Auxiliary battery power supply Ignition switch off 11 to 14 V
E25-3 (SIG) - E25-1 (GND) Ignition switch power supply Ignition switch ON 11 to 14 V
E25-4 (CPUB) - E25-1 (GND) Auxiliary battery power supply Ignition switch off 11 to 14 V
E25-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the E25 front multiplex network door ECU LH connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E25-5 (BDRJ) - E25-1 (GND) Power window regulator motor power supply Ignition switch off 11 to 14 V
E25-2 (PWE) - Body ground Ground Always Below 1 Ω
E25-9 (SGND) - Body ground Ground Always Below 1 Ω


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: for LHD

E25-11 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
E25-12 (LIN2) - Body ground* LIN communication line Ignition switch ON Pulse generation
E25-13 (LIN3) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH (w/ Reverse Shift-linked Mirror, Double Locking System)


B338775E26
3.406,0.229 3.833,0.469 0.427,0.24 3.531,0.271 3.833,0.469 0.302,0.198 10 false E7

a.

Disconnect the E7 front multiplex network door ECU RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E7-6 (BDR) - E7-1 (GND) Auxiliary battery power supply Ignition switch off 11 to 14 V
E7-3 (SIG) - E7-1 (GND) Ignition switch power supply Ignition switch ON 11 to 14 V
E7-4 (CPUB) - E7-1 (GND) Auxiliary battery power supply Ignition switch off 11 to 14 V
E7-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the E7 front multiplex network door ECU RH connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E7-5 (BDRJ) - E7-1 (GND) Power window regulator motor power supply Ignition switch off 11 to 14 V
E7-2 (PWE) - Body ground Ground Always Below 1 Ω
E7-9 (SGND) - Body ground Ground Always Below 1 Ω


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: for RHD

E7-11 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
E7-12 (LIN2) - Body ground* LIN communication line Ignition switch ON Pulse generation
E7-13 (LIN3) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR MULTIPLEX NETWORK DOOR ECU LH (w/ Double Locking System)


B340249E15
4.094,0.219 4.49,0.458 0.396,0.24 4.177,0.26 4.49,0.458 0.313,0.198 10 false F16

a.

Disconnect the F16 rear multiplex network door ECU LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F16-4 (BDR) - F16-1 (GND) Auxiliary battery power supply Ignition switch off 11 to 14 V
F16-12 (SIG) - F16-1 (GND) Ignition switch power supply Ignition switch ON 11 to 14 V
F16-11 (CPUB) - F16-1 (GND) Auxiliary battery power supply Ignition switch off 11 to 14 V
F16-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the F16 rear multiplex network door ECU LH connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F16-3 (BDRJ) - F16-1 (GND) Power window regulator motor power supply Ignition switch off 11 to 14 V
F16-2 (PWE) - Body ground Ground Always Below 1 Ω
F16-9 (SGND) - Body ground Ground Always Below 1 Ω


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F16-22 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
F16-23 (LIN3) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR MULTIPLEX NETWORK DOOR ECU RH (w/ Double Locking System)


B340249E16
4.094,0.219 4.49,0.458 0.396,0.24 4.219,0.26 4.531,0.458 0.313,0.198 10 false F5

a.

Disconnect the F5 rear multiplex network door ECU RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F5-4 (BDR) - F5-1 (GND) Auxiliary battery power supply Ignition switch off 11 to 14 V
F5-12 (SIG) - F5-1 (GND) Ignition switch power supply Ignition switch ON 11 to 14 V
F5-11 (CPUB) - F5-1 (GND) Auxiliary battery power supply Ignition switch off 11 to 14 V
F5-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the F5 rear multiplex network door ECU RH connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F5-3 (BDRJ) - F5-1 (GND) Power window regulator motor power supply Ignition switch off 11 to 14 V
F5-2 (PWE) - Body ground Ground Always Below 1 Ω
F5-9 (SGND) - Body ground Ground Always Below 1 Ω


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F5-22 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
F5-23 (LIN3) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E453982C01
1.083,3.198 1.49,3.458 0.406,0.26 3.24,3.198 3.646,3.458 0.406,0.26 5.448,3.208 5.854,3.469 0.406,0.26 3.24,7.708 3.646,7.969 0.406,0.26 1.823,4.542 2.229,4.802 0.406,0.26 5.385,4.479 5.792,4.74 0.406,0.26 1.125,6.177 1.531,6.438 0.406,0.26 3.573,6.115 3.979,6.375 0.406,0.26 6.25,6.146 6.656,6.406 0.406,0.26 5.271,6.146 5.677,6.406 0.406,0.26 1.625,1.781 1.906,1.781 false 1.625,1.427 1.906,1.427 false 1.625,1.115 1.906,1.115 false 1.573,0.604 1.573,0.24 1.573,0.24 1.781,0.24 false 1.99,1.729 2.302,1.927 0.313,0.198 10 false D14 1.979,1.063 2.292,1.26 0.313,0.198 10 false D12 1.99,1.375 2.302,1.573 0.313,0.198 10 false D11 3.75,0.927 3.906,1.125 0.156,0.198 10 false A 1.833,0.177 2.146,0.375 0.313,0.198 10 false *1 5.531,3.271 5.844,3.469 0.313,0.198 10 false D12 3.323,3.271 3.635,3.469 0.313,0.198 10 false D11 1.177,3.271 1.49,3.469 0.313,0.198 10 false D14 3.417,7.76 3.573,7.958 0.156,0.198 10 false A 0.833,1.031 1.146,1.229 0.313,0.198 10 false 4H 0.854,1.646 1.167,1.844 0.313,0.198 10 false 4F 0.854,2.01 1.167,2.208 0.313,0.198 10 false 4L 0.865,2.229 1.177,2.427 0.313,0.198 10 false 4K 5.823,1.042 6.135,1.24 0.313,0.198 10 false 4D 5.813,1.615 6.125,1.813 0.313,0.198 10 false 4A 1.958,4.615 2.271,4.813 0.313,0.198 10 false 4A 5.51,4.542 5.823,4.74 0.313,0.198 10 false 4D 1.271,6.24 1.583,6.438 0.313,0.198 10 false 4F 3.688,6.177 4,6.375 0.313,0.198 10 false 4H 6.417,6.208 6.729,6.406 0.313,0.198 10 false 4L 5.406,6.219 5.719,6.417 0.313,0.198 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the driver side junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A-11 (GND1) - Body ground Ground Always Below 1 Ω
A-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
A-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-32 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage and waveform according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D11-1 (FLCY) - Body ground Courtesy light switch LH input Front door LH open Below 1 V
Front door LH closed 4.7 to 5.3 V
D14-18 (L2) - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
Driver door key cylinder off Pulse generation
D14-17 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
Driver door key cylinder off Pulse generation
5D-16 - Body ground LIN communication line Ignition switch ON Pulse generation
5H-24 - Body ground LIN communication line Ignition switch ON Pulse generation
5H-25 - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D11-6 (FRCY) - Body ground Courtesy light switch RH input Front door RH open Below 1 V
Front door RH closed 4.7 to 5.3 V
D14-18 (L2) - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
Driver door key cylinder off Pulse generation
D14-17 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
Driver door key cylinder off Pulse generation
4A-40 - Body ground LIN communication line Ignition switch ON Pulse generation
4H-33 - Body ground LIN communication line Ignition switch ON Pulse generation
4H-34 - Body ground LIN communication line Ignition switch ON Pulse generation