When the ignition switch is ON, the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is operated by the multiplex network master switch assembly. The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has motor, regulator and ECU functions.
for LHD, w/o Reverse Shift-linked Mirror:
for LHD, w/ Reverse Shift-linked Mirror:
for RHD, w/o Reverse Shift-linked Mirror:
for RHD, w/ Double Locking System:
The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been replaced with a new one, initialize the power window control system.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
Inspect the fuses for circuits related to this system before performing the following procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Door P/W Up SW | Driver door power window manual up switch signal | OFF or ON | OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated |
- |
| D Door P/W Down SW | Driver door power window manual down switch signal | OFF or ON | OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated |
- |
| Tester Display |
|---|
| D Door P/W Up SW |
| D Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly) |
Disconnect the E20* or E2*2 front power window regulator motor assembly connector.
*1: for LHD
*2: for RHD
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E20)Location & Routingewd_type=routing;type=c;code=E20 Click Connector(E20)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly LHewd_type=component;type=c;code=E20;pinno=10,1,7 |
||
| E20-10 (UP) - E20-1 (GND) | ·
Ignition switch to ON ·
Multiplex network master switch assembly (driver side switch) OFF → UP (manual operation) |
11 to 14 V → Below 1 V |
| E20-7 (DOWN) - E20-1 (GND) | ·
Ignition switch to ON ·
Multiplex network master switch assembly (driver side switch) OFF → DOWN (manual operation) |
11 to 14 V → Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E2)Location & Routingewd_type=routing;type=c;code=E2 Click Connector(E2)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly RHewd_type=component;type=c;code=E2;pinno=10,1,7 |
||
| E2-10 (UP) - E2-1 (GND) | ·
Ignition switch to ON ·
Multiplex network master switch assembly (driver side switch) OFF → UP (manual operation) |
11 to 14 V → Below 1 V |
| E2-7 (DOWN) - E2-1 (GND) | ·
Ignition switch to ON ·
Multiplex network master switch assembly (driver side switch) OFF → DOWN (manual operation) |
11 to 14 V → Below 1 V |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
*1: for LHD
*2: for RHD
Disconnect the E32*1 or E14*2 multiplex network master switch assembly connector.
Disconnect the E20*1 or E2*2 front power window regulator motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E32,E20)Location & Routingewd_type=routing;type=c,c;code=E32,E20 Click Connector(E32)Body>Front Door Wire LH / Front Door Wire RH>Multiplex Network Master Switch Assemblyewd_type=component;type=c;code=E32;pinno=20,15 Click Connector(E20)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly LHewd_type=component;type=c;code=E20;pinno=10,7 |
||
| E32-20 (UP) - E20-10 (UP) | Always | Below 1 Ω |
| E32-15 (DOWN) - E20-7 (DOWN) | Always | Below 1 Ω |
| E32-20 (UP) or E20-10 (UP) - Body ground | Always | 10 kΩ or higher |
| E32-15 (DOWN) or E20-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E14,E2)Location & Routingewd_type=routing;type=c,c;code=E14,E2 Click Connector(E14)Body>Front Door Wire LH / Front Door Wire RH>Multiplex Network Master Switch Assemblyewd_type=component;type=c;code=E14;pinno=20,15 Click Connector(E2)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly RHewd_type=component;type=c;code=E2;pinno=10,7 |
||
| E14-20 (UP) - E2-10 (UP) | Always | Below 1 Ω |
| E14-15 (DOWN) - E2-7 (DOWN) | Always | Below 1 Ω |
| E14-20 (UP) or E2-10 (UP) - Body ground | Always | 10 kΩ or higher |
| E14-15 (DOWN) or E2-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG